What did you do to your truck today! - Page 138 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**67cheby** · 02-17-2012, 10:20 PM

Nice job on the kick panels
Posted via Mobile Device

74baggedbug · 02-17-2012, 10:35 PM

Thanks

Posted via Mobile Device

67Slider · 02-17-2012, 11:15 PM

Installed the 94 amp alt from an 86 silverado. Internally regulated, 3 wire set up. Fixed the amp gauge too.
[IMG]

[/IMG]

shawno72 · 02-18-2012, 02:04 AM

Quote:

Originally Posted by Newtz67

Got my tires remounted on the rallyes and got them on the truck. Much better!

The rallies look good Newt!!

Posted via Mobile Device

wrwelton · 02-18-2012, 08:54 AM

I installed the sound deadening insulation and started restoring the heater equiptment. I had several heaters and vent boxes to choose from so I could take the best parts of many. I sandblasted parts and applied rustmort over night. Paint it all tomorrow.

bigdog57 · 02-18-2012, 12:26 PM

I have been upgrading my timing chain and sprockets. Its been a real pita. I've had the most problem out of the harmonic balancer installation tool than any of it. But we are almost done. Just fixing to check on the timing.

Newtz67 · 02-18-2012, 02:47 PM

Quote:

Originally Posted by shawno72

The rallies look good Newt!!

Posted via Mobile Device

Thanks bro!

67lowered · 02-18-2012, 11:52 PM

Quote:

Originally Posted by ffk

made a filler panel for firewall on driver side to match passenger side..hand formed the old fashined way...a small torch , hammer and a round bar ..heated and hammered radius on panel...also cut vent cowl shorter..no need will have vintage air...im going to put a 61/2 speaker in there and a rubber grommet for the wireing harness

ffk,, nice tin work, bet that took some time,
I gotta do mine, thanks the inspiration

Tomahawk30 · 02-19-2012, 12:46 AM

Tinkered on the new C10 for a while today. Replaced the LOOOONG van-style oil filler tube with a oil cap / grommet, checked plugs / gaps, tested compression on all cylinders, and installed a squarebore carb to q-jet intake adapter (previous owner had installed edelbrock directly to the original intake). The old 350 still isn't running right, but it looks like the timing is WAY off. I think the previous owner dropped the distributor in without setting TDC on 1. It'll run, but the #1 wire has to be clear over past the normal #8 position, and the vacuum advance doesn't appear to be working well either. Probably going to hold off on any more troubleshooting until the new HEI shows up. Hopefully the new install will clear up all these little issues...

I also crawled underneath to check out the saddle tank setup. The tanks look great from underneath, but who knows what the inside looks like. The switch and saddle tank fuel lines are disconnected but all there if I decide to hook it back up. For now I might pull the new-ish tank out of my donor cab tomorrow and see how clean it is.

DaBigKahuna · 02-19-2012, 09:51 PM

Spent a great day hanging out with forum members JohnOro and V-Dog.

Oh, and we swapped out the water pump on my truck.

Thank you for the help and conversation. It was much appreciated!

MARIOS68PANEL · 02-19-2012, 10:42 PM

Bought it and brought it home. after installing a new master cylinder and bleeding breaks. 1967

Newtz67 · 02-19-2012, 10:47 PM

Nice! Congrats!

wrwelton · 02-20-2012, 08:37 AM

Installed heater and rest of insulation. Ordered the adapter for 72 gas pedal to fit earlier cab from member. Watched youtube video on installation of harness.Just ordered wiring harness from American Auto Wire on ebay. $479
.

69-72 Truck - YouTube

Hard Luck · 02-21-2012, 04:50 AM

Turned my truck into this!

Redleg · 02-21-2012, 08:53 AM

Quote:

Originally Posted by Hard Luck

Turned my truck into this!

First off gorgeous truck, second, what is that hanging off the E-Brake release?

no moa · 02-21-2012, 09:20 AM

Quote:

Originally Posted by Redleg

First off gorgeous truck, second, what is that hanging off the E-Brake release?

Pine air freshner
Posted via Mobile Device

Redleg · 02-21-2012, 09:40 AM

Quote:

Originally Posted by no moa

Pine air freshner
Posted via Mobile Device

thought thats probably what it was, but almost looked like a yellow thong... So i had to ask!

aventur1 · 02-21-2012, 09:46 AM

Unplugged interior wire harness, I have a harness that has excellent fuse box writing and it has like new wires, very clean so replacing my old one. Removed dash and replaced the green turn signal and high beem red color caps with blue. Going with blue lghts in dash so thought why not blue turn signal and high beem. Used a blue plastic and cut out and glued on the cardboard supports in dash. Took dash pad in to get recovered in leather like my side panels are. Going to take a dremal and polish up fuse tabs in the fuse box before I install.

mcmlxix · 02-21-2012, 10:18 AM

I ddnt do anything to it... bit it sprung a leak on me... heater core.... damn.

74baggedbug · 02-21-2012, 02:16 PM

Still working on it
Posted via Mobile Device

74baggedbug · 02-21-2012, 02:17 PM

....

Katrina/10 · 02-21-2012, 02:27 PM

Quote:

Originally Posted by wrwelton

Installed heater and rest of insulation. Ordered the adapter for 72 gas pedal to fit earlier cab from member. Watched youtube video on installation of harness.Just ordered wiring harness from American Auto Wire on ebay. $479
.69-72 Truck - YouTube

Got any pics of that adapter installed?

1quik70 · 02-21-2012, 04:38 PM

Same thing I do everyday Pinky, Jumped in her and went to work! Thought about washing it but decided it was pointless!

74baggedbug · 02-21-2012, 07:18 PM

Posted via Mobile Device

*72chevy383* · 02-21-2012, 10:15 PM

Put on my No Limit Shock relocators.

02-17-2012, 10:20 PM	#3426
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: What did you do to your truck today! Nice job on the kick panels Posted via Mobile Device __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

02-17-2012, 10:35 PM	#3427
74baggedbug Registered User Join Date: Oct 2011 Location: Houston tx Posts: 701	Re: What did you do to your truck today! Thanks Posted via Mobile Device

02-17-2012, 11:15 PM	#3428
67Slider Registered User Join Date: Mar 2010 Location: Pueblo West, CO Posts: 944	Re: What did you do to your truck today! Installed the 94 amp alt from an 86 silverado. Internally regulated, 3 wire set up. Fixed the amp gauge too. [IMG][/IMG] __________________ 67 C10 Stepside 66 Mustang Coupe 99 Burb 2500

02-18-2012, 08:54 AM	#3430
wrwelton Registered User Join Date: Mar 2006 Location: massachusetts Posts: 180	Re: What did you do to your truck today! I installed the sound deadening insulation and started restoring the heater equiptment. I had several heaters and vent boxes to choose from so I could take the best parts of many. I sandblasted parts and applied rustmort over night. Paint it all tomorrow. Attached Images __________________ I know I can! I know i can! 72 K20 Restoration

02-18-2012, 12:26 PM	#3431
bigdog57 Registered User Join Date: Sep 2011 Location: krugerville Tx Posts: 81	Re: What did you do to your truck today! I have been upgrading my timing chain and sprockets. Its been a real pita. I've had the most problem out of the harmonic balancer installation tool than any of it. But we are almost done. Just fixing to check on the timing. __________________ Bigdog

02-19-2012, 12:46 AM	#3434
Tomahawk30 Registered User Join Date: Jun 2010 Location: Russellville, KY Posts: 956	Re: What did you do to your truck today! Tinkered on the new C10 for a while today. Replaced the LOOOONG van-style oil filler tube with a oil cap / grommet, checked plugs / gaps, tested compression on all cylinders, and installed a squarebore carb to q-jet intake adapter (previous owner had installed edelbrock directly to the original intake). The old 350 still isn't running right, but it looks like the timing is WAY off. I think the previous owner dropped the distributor in without setting TDC on 1. It'll run, but the #1 wire has to be clear over past the normal #8 position, and the vacuum advance doesn't appear to be working well either. Probably going to hold off on any more troubleshooting until the new HEI shows up. Hopefully the new install will clear up all these little issues... I also crawled underneath to check out the saddle tank setup. The tanks look great from underneath, but who knows what the inside looks like. The switch and saddle tank fuel lines are disconnected but all there if I decide to hook it back up. For now I might pull the new-ish tank out of my donor cab tomorrow and see how clean it is. __________________ 1979 Silverado C10 Shortbox - Photo Album 1977 Silverado K20 Camper Special - Photo Album 1972 C10 Custom Deluxe Highlander - sold 1971 Cheyenne Super Longhorn -sold 1972 Cheyenne Super SWB 4x4 -sold, bought back, sold again... I'm dumb. 1970 Chevy C10 SWB "Sprout" -sold 1972 Cheyenne K20 -sold 1969 GMC Shortbox Stepside 4x4 -sold 1972 GMC Jimmy 4x4 -sold

02-19-2012, 09:51 PM	#3435
DaBigKahuna Registered User Join Date: Mar 2011 Location: Disneyland, CA Posts: 486	Re: What did you do to your truck today! Spent a great day hanging out with forum members JohnOro and V-Dog. Oh, and we swapped out the water pump on my truck. Thank you for the help and conversation. It was much appreciated!

02-19-2012, 10:42 PM	#3436
MARIOS68PANEL Active Member Join Date: Mar 2005 Location: North Highlands. California Posts: 449	Re: What did you do to your truck today! Bought it and brought it home. after installing a new master cylinder and bleeding breaks. 1967 Attached Images __________________ 67 short step 71 Custom

02-19-2012, 10:47 PM	#3437
Newtz67 Registered User Join Date: Mar 2010 Location: A t w a t e r, Ca Posts: 1,201	Re: What did you do to your truck today! Nice! Congrats! __________________ My '67 short wide Our '68 Burb My '04 Z71 The '54 Belair The '69 Cadillac

02-21-2012, 04:50 AM	#3439
Hard Luck I've got grease on my mind. Join Date: Sep 2007 Location: Oly, Wa Posts: 481	Re: What did you do to your truck today! Turned my truck into this! Attached Images

02-21-2012, 09:46 AM	#3443
aventur1 Registered User Join Date: Aug 2007 Location: Boise, Idaho Posts: 676	Re: What did you do to your truck today! Unplugged interior wire harness, I have a harness that has excellent fuse box writing and it has like new wires, very clean so replacing my old one. Removed dash and replaced the green turn signal and high beem red color caps with blue. Going with blue lghts in dash so thought why not blue turn signal and high beem. Used a blue plastic and cut out and glued on the cardboard supports in dash. Took dash pad in to get recovered in leather like my side panels are. Going to take a dremal and polish up fuse tabs in the fuse box before I install. __________________ 1968 4x4 Frame, with a 67 Cab and Bed A Shorter Step 1999 Dodge 2500 Cummins Diesel

02-21-2012, 10:18 AM	#3444
mcmlxix Collector of Projects Join Date: Apr 2003 Location: Las Vegas Posts: 3,106	Re: What did you do to your truck today! I ddnt do anything to it... bit it sprung a leak on me... heater core.... damn. __________________ Rich 1972 K5 Blazer CST Click HERE D60 BIG BRAKE UPGRADE Click HERE

02-21-2012, 02:16 PM	#3445
74baggedbug Registered User Join Date: Oct 2011 Location: Houston tx Posts: 701	Re: What did you do to your truck today! Still working on it Posted via Mobile Device

02-21-2012, 02:17 PM	#3446
74baggedbug Registered User Join Date: Oct 2011 Location: Houston tx Posts: 701	Re: What did you do to your truck today! .... Last edited by 74baggedbug; 02-21-2012 at 02:18 PM. Reason: Double pic

02-21-2012, 04:38 PM	#3448
1quik70 Registered User Join Date: Apr 2010 Location: Jeffersonville, Indiana Posts: 136	Re: What did you do to your truck today! Same thing I do everyday Pinky, Jumped in her and went to work! Thought about washing it but decided it was pointless!



Register or Log In To remove these advertisements.

02-21-2012, 07:18 PM	#3449
74baggedbug Registered User Join Date: Oct 2011 Location: Houston tx Posts: 701	Re: What did you do to your truck today! Posted via Mobile Device

02-21-2012, 10:15 PM	#3450
72chevy383 Account Suspended Join Date: Feb 2010 Location: Bessemer City, NC Posts: 347	Re: What did you do to your truck today! Put on my No Limit Shock relocators. Attached Images

Register or Log In To remove these advertisements.