cannot collapse intermediate shaft... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

elf w/capital T · 06-27-2012, 09:37 PM

i completley removed the plastic 'rivets' let it soak with pb blaster, and this is day 3 i still cannot get it to collapse, any tricks any one knows of?

gringoloco · 06-27-2012, 10:57 PM

How did you remove the plastic? I usually use a propane torch and cook 'em out. The plastic will swell and come out the holes looking like worms. Burn 'til it stops oozing. Whack it with a big hammer 'til it collapses...

Portmod7 · 06-28-2012, 12:30 AM

I had to get a little aggressive with mine, I had the shaft completely out of the column. There's no way mine would have ever moved without beating on it a little.
Posted via Mobile Device

elf w/capital T · 06-28-2012, 10:14 AM

i drilled them out and used a scribe to get the remainders out, and i have soaked it, beat it on the ground very hard, soak it again beat it on the cement some more and still wont budge, ill keep trying, i dont want to hit too hard and bend or break the rag joint

elf w/capital T · 06-28-2012, 11:57 AM

nevermind i was being a little girl and just had to hit it even harder, the thing was covered in rust.

sambudo · 03-22-2014, 02:00 AM

Quote:

Originally Posted by gringoloco

How did you remove the plastic? I usually use a propane torch and cook 'em out. The plastic will swell and come out the holes looking like worms. Burn 'til it stops oozing. Whack it with a big hammer 'til it collapses...

Good information.

06-27-2012, 09:37 PM	#1
elf w/capital T Registered User Join Date: Feb 2011 Location: North Carolina Posts: 994	cannot collapse intermediate shaft... i completley removed the plastic 'rivets' let it soak with pb blaster, and this is day 3 i still cannot get it to collapse, any tricks any one knows of?

06-27-2012, 10:57 PM	#2
gringoloco A guy with a truck Join Date: Sep 2005 Location: Germany, for now Posts: 5,921	Re: cannot collapse intermediate shaft... How did you remove the plastic? I usually use a propane torch and cook 'em out. The plastic will swell and come out the holes looking like worms. Burn 'til it stops oozing. Whack it with a big hammer 'til it collapses... __________________ -Chris Instagram _elgringoloco_ '70 Short-Wide How to: Ruin a perfectly good C10 ‘70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd '72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD) '72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD) '05 Yukon Daily Driven (not so stock) Yukon (SOLD) ‘07 Yukon Denali (daily) Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy

06-28-2012, 12:30 AM	#3
Portmod7 Registered User Join Date: Dec 2004 Location: Aztec, NM Posts: 388	Re: cannot collapse intermediate shaft... I had to get a little aggressive with mine, I had the shaft completely out of the column. There's no way mine would have ever moved without beating on it a little. Posted via Mobile Device __________________ Super Blue - 1968 C-10 Short Stepside Fastburn 385, 4-Speed Sag. on the Column, Coleman 9" Floater w/Detroit TrueTrac

06-28-2012, 10:14 AM	#4
elf w/capital T Registered User Join Date: Feb 2011 Location: North Carolina Posts: 994	Re: cannot collapse intermediate shaft... i drilled them out and used a scribe to get the remainders out, and i have soaked it, beat it on the ground very hard, soak it again beat it on the cement some more and still wont budge, ill keep trying, i dont want to hit too hard and bend or break the rag joint

06-28-2012, 11:57 AM	#5
elf w/capital T Registered User Join Date: Feb 2011 Location: North Carolina Posts: 994	Re: cannot collapse intermediate shaft... nevermind i was being a little girl and just had to hit it even harder, the thing was covered in rust.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.