Mr. Gasket Carb Base Plate Installation? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

savatreatabvr · 11-06-2012, 07:59 PM

I bought a Mr. Gasket Carburetor Adapter Kit from Checker Auto and on the back it says "ADAPTS SQUARE FLANGE CARBURETOR TO QUADRAJET SPREADBORE MANIFOLD"! That makes me believe I can use this to mount my Squarebore Edelbrock 1407 carb to my factory 454 Spreadbore intake manifold but the adapter looks like it's a Spreadbore to Squarebore! Can somebody set me straight?

INSIDIOUS '86 · 11-06-2012, 09:45 PM

Take the ugly end and point it down and the round 4 hole side up. Spray toilet water on it and install carb add fuel and be amazed at how easy it is to get to idle without hardly doing anything cause its a edelbrock
Posted via Mobile Device

savatreatabvr · 11-06-2012, 11:52 PM

This is the one I bought, looks like pic #1 is the top which would make it an Spreadbore to Squarebore adapter, am I right?

Quote:

Originally Posted by INSIDIOUS '86

Take the ugly end and point it down and the round 4 hole side up. Spray toilet water on it and install carb add fuel and be amazed at how easy it is to get to idle without hardly doing anything cause its a edelbrock
Posted via Mobile Device

INSIDIOUS '86 · 11-07-2012, 01:07 AM

I see no pics...
Posted via Mobile Device

savatreatabvr · 11-07-2012, 01:45 AM

Sorry about that, my internet connection tends to drop data sometimes for some reason!

savatreatabvr · 11-07-2012, 01:49 AM

And a smaller pic of one!

Quote:

Originally Posted by savatreatabvr

Sorry about that, my internet connection tends to drop data sometimes for some reason!

INSIDIOUS '86 · 11-07-2012, 01:59 AM

Well that will turn your dual plane more into a single plane. While it will work, it still will not be worth any power over the quadrajet that you have already. The cast iron intake is like forcing asthma on your engine. Don't matter what you put on top of it the throat (intake) still wont flow.
Posted via Mobile Device

85sierraclassic · 11-07-2012, 05:00 AM

the last pic is the way you need to put it on make sure your throttle blades clear ok. but its universal so just flip it for what ever your doing. just make sure to hold your studs in from the bottom before its mounted or you get to take it back off and try again lol

jjzepplin · 11-07-2012, 05:16 AM

Quote:

Originally Posted by 85sierraclassic

the last pic is the way you need to put it on make sure your throttle blades clear ok. but its universal so just flip it for what ever your doing. just make sure to hold your studs in from the bottom before its mounted or you get to take it back off and try again lol

And spin some nuts on them so they don't fall into your engine..

11-06-2012, 09:45 PM	#2
INSIDIOUS '86 Registered User Join Date: Jul 2009 Location: washington Posts: 4,178	Re: Mr. Gasket Carb Base Plate Installation? Take the ugly end and point it down and the round 4 hole side up. Spray toilet water on it and install carb add fuel and be amazed at how easy it is to get to idle without hardly doing anything cause its a edelbrock Posted via Mobile Device __________________ 377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511

11-07-2012, 01:07 AM	#4
INSIDIOUS '86 Registered User Join Date: Jul 2009 Location: washington Posts: 4,178	Re: Mr. Gasket Carb Base Plate Installation? I see no pics... Posted via Mobile Device __________________ 377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511

11-07-2012, 01:45 AM	#5
savatreatabvr Registered User Join Date: Oct 2011 Location: phoenix, az Posts: 508	Re: Mr. Gasket Carb Base Plate Installation? Sorry about that, my internet connection tends to drop data sometimes for some reason!

11-07-2012, 01:59 AM	#7
INSIDIOUS '86 Registered User Join Date: Jul 2009 Location: washington Posts: 4,178	Re: Mr. Gasket Carb Base Plate Installation? Well that will turn your dual plane more into a single plane. While it will work, it still will not be worth any power over the quadrajet that you have already. The cast iron intake is like forcing asthma on your engine. Don't matter what you put on top of it the throat (intake) still wont flow. Posted via Mobile Device __________________ 377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511

11-07-2012, 05:00 AM	#8
85sierraclassic Registered User Join Date: Dec 2010 Location: auburn ne Posts: 230	Re: Mr. Gasket Carb Base Plate Installation? the last pic is the way you need to put it on make sure your throttle blades clear ok. but its universal so just flip it for what ever your doing. just make sure to hold your studs in from the bottom before its mounted or you get to take it back off and try again lol __________________ 85 GMC sierra classic : 350, 4spd, 205, 3.42s, 35s

11-06-2012, 07:59 PM	#1
savatreatabvr Registered User Join Date: Oct 2011 Location: phoenix, az Posts: 508	Mr. Gasket Carb Base Plate Installation? I bought a Mr. Gasket Carburetor Adapter Kit from Checker Auto and on the back it says "ADAPTS SQUARE FLANGE CARBURETOR TO QUADRAJET SPREADBORE MANIFOLD"! That makes me believe I can use this to mount my Squarebore Edelbrock 1407 carb to my factory 454 Spreadbore intake manifold but the adapter looks like it's a Spreadbore to Squarebore! Can somebody set me straight?



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.