Pitman Arm Installation - The 1947 - Present Chevrolet & GMC Truck Message Board Network

mmsidaho · 11-14-2012, 03:53 PM

I'm working on a 1972 C10 restoration I started several years ago, and I don't remember how far the pitman arm slides onto the splined shaft of the steering gearbox. In trying to install the new pitman arm, I can only get it to a point where there is still 3/8" to 1/2" of spine showing between the pitman arm and what would be a tight fit to the bottom of the steering gearbox. I've torqued the heck out of it with a 3/4" drive wratchet and socket and I blieve I've got the threaded end of the splined shaft coming out below the nut. I'm at work and don't have any pictures right now, but could take some later on.

Any idea if this is the normal spot where the pitman arm belongs? I'm almost afraid of what it might take if I have to force it any further up the splined shaft of the steering gearbox.

Thanks.

68gmsee · 11-14-2012, 04:39 PM

The pitman arm/gearbox are tapered and it will only go in as far as the taper will allow it. Pics of mine. (The leak is from a bad hose I have.)

mmsidaho · 11-14-2012, 09:31 PM

Mine is on about the same amount now, so I should be good.

Thanks for the help and the pics!
Posted via Mobile Device

SIXT8LOU · 05-12-2016, 04:04 PM

hello! i know this is a old thread, but i am having the same issue on my truck, the pitman arm does not slide all the way up as it did with the old arm(im installing all new front end) i can see where the old one left its mark, and im still bout a 1/4 inch short of the old mark. i have a identical new replacement part (moog 6143). I appreciate your help if possible. thank you!

slikside · 05-12-2016, 05:54 PM

No experience with this, but it looks like it would be easy to put the arm on up-side-down. Make sure you have it going on the proper way.

sprint_9 · 05-12-2016, 11:29 PM

Quote:

Originally Posted by SIXT8LOU

hello! i know this is a old thread, but i am having the same issue on my truck, the pitman arm does not slide all the way up as it did with the old arm(im installing all new front end) i can see where the old one left its mark, and im still bout a 1/4 inch short of the old mark. i have a identical new replacement part (moog 6143). I appreciate your help if possible. thank you!

Make sure you torque the nut, if you have power steering it is torqued to 180 ft/lbs.

11-14-2012, 03:53 PM	#1
mmsidaho Registered User Join Date: Feb 2012 Location: Meridian, Idaho Posts: 37	Pitman Arm Installation I'm working on a 1972 C10 restoration I started several years ago, and I don't remember how far the pitman arm slides onto the splined shaft of the steering gearbox. In trying to install the new pitman arm, I can only get it to a point where there is still 3/8" to 1/2" of spine showing between the pitman arm and what would be a tight fit to the bottom of the steering gearbox. I've torqued the heck out of it with a 3/4" drive wratchet and socket and I blieve I've got the threaded end of the splined shaft coming out below the nut. I'm at work and don't have any pictures right now, but could take some later on. Any idea if this is the normal spot where the pitman arm belongs? I'm almost afraid of what it might take if I have to force it any further up the splined shaft of the steering gearbox. Thanks.

11-14-2012, 04:39 PM	#2
68gmsee Active Member Join Date: Jul 2007 Location: Centrally located between Houston, Austin and Waco. BCS area. Posts: 7,947	Re: Pitman Arm Installation The pitman arm/gearbox are tapered and it will only go in as far as the taper will allow it. Pics of mine. (The leak is from a bad hose I have.) Attached Images __________________ 68 GMC 250/3 speed Saginaw p/b p/s 69 Chevy 350/350 currently in pieces still lookin for a cab 06 Trailblazer I just want a vehicle that I can work on, that won't talk to me, leave error msgs or keep track of how I drive...

11-14-2012, 09:31 PM	#3
mmsidaho Registered User Join Date: Feb 2012 Location: Meridian, Idaho Posts: 37	Re: Pitman Arm Installation Mine is on about the same amount now, so I should be good. Thanks for the help and the pics! Posted via Mobile Device

05-12-2016, 04:04 PM	#4
SIXT8LOU Registered User Join Date: Oct 2007 Location: Corona,Ca Posts: 146	Re: Pitman Arm Installation hello! i know this is a old thread, but i am having the same issue on my truck, the pitman arm does not slide all the way up as it did with the old arm(im installing all new front end) i can see where the old one left its mark, and im still bout a 1/4 inch short of the old mark. i have a identical new replacement part (moog 6143). I appreciate your help if possible. thank you! __________________ 68 C/10 short bed 77 C/20 silverado long bed 05 GMC Duramax Crew

05-12-2016, 05:54 PM	#5
slikside Registered User Join Date: Jun 2010 Location: San Diego Co. Posts: 1,179	Re: Pitman Arm Installation No experience with this, but it looks like it would be easy to put the arm on up-side-down. Make sure you have it going on the proper way. __________________ 1972 Chevy C-10, SWB, Fleet, 350/350, PS, PB, HEI, mostly stock, Survivor.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.