fleetside vs stepside question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

moggey01 · 01-25-2013, 04:40 AM

Which bed option will accept the biggest tire?? I want to run up to a 15 or 16 wide tire , and found a deal on a stepside bed. I dont know how big of a tire will fit with this bed.

70c10stepside · 01-25-2013, 05:04 AM

Idk about fleet side, but my 70 has 295s. Its really close. Maybe, another itch, 2 would be pushing it. Not sure on offset of wheels
Posted via Mobile Device

CC69Rat · 01-25-2013, 10:11 AM

I have both trucks. One fleetside, one stepside. No question about it, with stock unmodified wheel tubs the fleetside gives you more room for tires.

The key here is knowing which rear end housing your truck has in it. The earlier rear housings were 55.5" long if you measure from the inside edge of one brake backing plate to the other. The later ones were 57" respectively. I guess you can see where it might be a deal breaker if someone has the early rear end and tells you "x backspacing" will work .. then on yours if you have the longer one it's now off .75" on each side.

But, for the most part.

Fleetside bed:

Early rear end housing. 20x10 with 5" Backspacing
Late rear end housing. 20x10 with 5.5" Backspacing.

If your truck is really low, you might want to go a little deeper (more BS) but most guys running about 6" drop in the rear run this size wheel with a 295/40/20 in the back. I personally went with a 295/45/20 for a little more sidewall.

Example - my fleetside = late rear housing and a 20x10 with 6" BS. I did this because of the added tire size, plus my rear discs.

On my stepside I had 20x8.5 with 4.75" BS and an early rear housing. It was really tight with a 255/45/20.

If you want Big meats .. go fleetside.

moggey01 · 01-25-2013, 01:59 PM

my housing is going to be cut to fit the wheels , it has no ends now. The ride height should be about 5.5 inches at the frame maybe a little higher on the rear. I am using big aluminum tubs no matter what I do , I want to use a 14'' wide wheel or atleast a 12''. Thanks for the info I did not know the width of the early housing and was trying to figure that out. I have a chromoly fabbed housing that is 60'' with no ends. I need to find out how close the frame is to the inside of the fender on the step side.

01-25-2013, 04:40 AM	#1
moggey01 Registered User Join Date: Apr 2011 Location: Houston Texas Posts: 315	fleetside vs stepside question Which bed option will accept the biggest tire?? I want to run up to a 15 or 16 wide tire , and found a deal on a stepside bed. I dont know how big of a tire will fit with this bed.

01-25-2013, 05:04 AM	#2
70c10stepside Registered User Join Date: Jun 2011 Location: Taylorsville, Georgia Posts: 482	Re: fleetside vs stepside question Idk about fleet side, but my 70 has 295s. Its really close. Maybe, another itch, 2 would be pushing it. Not sure on offset of wheels Posted via Mobile Device

01-25-2013, 10:11 AM	#3
CC69Rat Registered User Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,212	Re: fleetside vs stepside question I have both trucks. One fleetside, one stepside. No question about it, with stock unmodified wheel tubs the fleetside gives you more room for tires. The key here is knowing which rear end housing your truck has in it. The earlier rear housings were 55.5" long if you measure from the inside edge of one brake backing plate to the other. The later ones were 57" respectively. I guess you can see where it might be a deal breaker if someone has the early rear end and tells you "x backspacing" will work .. then on yours if you have the longer one it's now off .75" on each side. But, for the most part. Fleetside bed: Early rear end housing. 20x10 with 5" Backspacing Late rear end housing. 20x10 with 5.5" Backspacing. If your truck is really low, you might want to go a little deeper (more BS) but most guys running about 6" drop in the rear run this size wheel with a 295/40/20 in the back. I personally went with a 295/45/20 for a little more sidewall. Example - my fleetside = late rear housing and a 20x10 with 6" BS. I did this because of the added tire size, plus my rear discs. On my stepside I had 20x8.5 with 4.75" BS and an early rear housing. It was really tight with a 255/45/20. If you want Big meats .. go fleetside. __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

01-25-2013, 01:59 PM	#4
moggey01 Registered User Join Date: Apr 2011 Location: Houston Texas Posts: 315	Re: fleetside vs stepside question my housing is going to be cut to fit the wheels , it has no ends now. The ride height should be about 5.5 inches at the frame maybe a little higher on the rear. I am using big aluminum tubs no matter what I do , I want to use a 14'' wide wheel or atleast a 12''. Thanks for the info I did not know the width of the early housing and was trying to figure that out. I have a chromoly fabbed housing that is 60'' with no ends. I need to find out how close the frame is to the inside of the fender on the step side.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.