Project "Shifted"

[f.monroe]

If you install lower motor mounts won't that raise the rear of the tails haft and make that angle worse? Or are you going to lower the entire assembly, motor and trans together to keep the same angle?
Frank
Posted via Mobile Device

[jmedero]

How come when I come over there is no beer on that cowl.......? Lol. Ill bring them next time.
Posted via Mobile Device

[RRC]

That's what I was wondering , the angle being 5 degrees is right . So did Nate think you might have just got the wrong motor mounts? Because mine set up at 5 degrees the trans x member is lower than yours. Mine looks like floppydoodle's
Posted via Mobile Device

[floppydoodle]

Bennett--G4L mine is a little less than halfway. Actually you can see where I had to shim the tail shaft up so my headers wouldn't hit my control arms. I am machining a 5/8 aluminum spacer to slide in there.
Posted via Mobile Device

[Hart_Rod]

Originally Posted by RRC

That's what I was wondering , the angle being 5 degrees is right . So did Nate think you might have just got the wrong motor mounts? Because mine set up at 5 degrees the trans x member is lower than yours. Mine looks like floppydoodle's
Posted via Mobile Device

What is the measurement of your motor mounts from the center of the lower mounting point to the tallest part of the motor mount?
Posted via Mobile Device

[Hart_Rod]

Originally Posted by floppydoodle

Bennett--G4L mine is a little less than halfway. Actually you can see where I had to shim the tail shaft up so my headers wouldn't hit my control arms. I am machining a 5/8 aluminum spacer to slide in there.
Posted via Mobile Device

Floppy what angle is yours set at? How high did you have to shim your carrier bearing?
Posted via Mobile Device

[floppydoodle]

Rob mine is at 5* like RRC and the carrier bearing is 2-1/2" shimmed up. From the tail shaft to the carrier bearing it runs parallel to the the frame.
Posted via Mobile Device

[Hart_Rod]

Originally Posted by floppydoodle

Rob mine is at 5* like RRC and the carrier bearing is 2-1/2" shimmed up. From the tail shaft to the carrier bearing it runs parallel to the the frame.
Posted via Mobile Device

What is the measurement of your motor mounts from the center of the lower mounting point to the tallest part of the motor mount? Also, what is the measurement from the bottom of your carrier bearing to the centerline of your driveshaft? Do you have a picture of the front of your engine?
Posted via Mobile Device

[floppydoodle]

I'll get pics and measurements tomorrow.
Posted via Mobile Device

[RRC]

Originally Posted by Hart_Rod

What is the measurement of your motor mounts from the center of the lower mounting point to the tallest part of the motor mount?
Posted via Mobile Device

I'm out camping .....but I will be home tomorrow and can measure that. Unless floppydoodle get it before I get home
Posted via Mobile Device

[FRENCHBLUE72]

Im tuned in on the driveline action... I agree there needs to be a good write up soon..

[RRC]

Rob my motor mount measures 8" from center of the lower hole to the top edge of mounting plate......
Posted via Mobile Device

[RRC]

Posted via Mobile Device Here is a pic from the front ....the motor is not set at 5 degrees in this pic.....
Posted via Mobile Device

[Hart_Rod]

Originally Posted by RRC

Rob my motor mount measures 8" from center of the lower hole to the top edge of mounting plate......
Posted via Mobile Device

Thanks Russ, mine measures the same. Where are you placing your angle finder to get your measurement?
Posted via Mobile Device

[RRC]

The surface of the tail shaft
Posted via Mobile Device

[Hart_Rod]

Originally Posted by RRC

The surface of the tail shaft
Posted via Mobile Device

Thanks Russ. Can you get one more measurement from the centerline of the lower engine mounting hole to the centerline of holes that the lower A frame bolt to? TIA
Posted via Mobile Device

[lolife99]

I assume everyone is getting their "5 degrees down" measurement with the frame rails level and not setting on the wheels?

[RRC]

That measurement is 4.5" .....I measured from the top of the lower control arm tube to the center or of the lower motor mount hole....
Posted via Mobile Device

[C10_ustacould]

Originally Posted by lolife99

I assume everyone is getting their "5 degrees down" measurement with the frame rails level and not setting on the wheels?

Good point Keith!

[lolife99]

Originally Posted by BucksSS

Good point Keith!

That's the only way to compare "apples-to-apples", here.

[Hart_Rod]

Originally Posted by RRC

That measurement is 4.5" .....I measured from the top of the lower control arm tube to the center or of the lower motor mount hole....
Posted via Mobile Device

Thanks. I think we found part of the difference, mine measures 5.0"...

Originally Posted by BucksSS

Good point Keith!

Yep

Originally Posted by lolife99

That's the only way to compare "apples-to-apples", here.

Thanks Keith, that's what I'm using as the reference. I should have mentioned it before.
Posted via Mobile Device

[RRC]

Yes my frame is level as well.....I wonder why there would be 1/2" difference ?
Posted via Mobile Device

[RRC]

Posted via Mobile Device Sorry Rob.....when you said yours was 5 I double checked and it is 5
The frame is still level the other question should be is the 5 degrees measured with the frame level or ride height ?
Posted via Mobile Device

[Hart_Rod]

Mine is with frame level.
Posted via Mobile Device

[RRC]

Originally Posted by Hart_Rod

Mine is with frame level.
Posted via Mobile Device

I have also heard that it should be measured at ride height ...not sure which is correct though. I could not lower my engine or the rack would hit.
Posted via Mobile Device
Posted via Mobile Device