Intake Manifold Gasket - The 1947 - Present Chevrolet & GMC Truck Message Board Network

skokie · 12-02-2003, 01:46 AM

Does anyone know the part number for the fel pro intake manifold gasket for a 350? Going to be using a edelbrock 2101 performer.

Thanks

Cat Fuzz · 12-02-2003, 01:52 AM

MS90314

jorgensensc · 12-02-2003, 02:03 AM

Mine was a 1205(pretty sure) performance gasket for an edelbrock rpm air gap. I highly suggest buying a good gasket and using the copper rtv sealant. You don't want to have to do this more than once!! Don't use the cork end pieces, just run a 1/4" bead on the ends. For best adhesion Put the sealant, (not on the ends), then the gaskets, torque down the manifold. Let it dry overnight. Remove the intake the next day. Check for gasket slippage and clean the gasket sealer off of the ports. Add sealant to ends, then put manifold back on and torque to specs. I did it this way and have had no leaks thusfar. Good luck and I hope this helps a little.

skokie · 12-02-2003, 02:05 AM

Yep it does. With any luck the manifold will be coming off either thursday or friday. Getting everything outta the way first and I have to wait for the adapter for my carb to arrive. Heres some pics of the manifold.
Cant wait to drop this thing on there.

skokie · 12-02-2003, 02:05 AM

#2

skokie · 12-02-2003, 02:06 AM

#3

Cat Fuzz · 12-02-2003, 02:10 AM

I don't know if anyone else does this, but when I installed my Edelbrock Performer, I used studs and nuts for everything. That way when you go to change the thermostat or something, there is less risk of stripping out the threads.

skokie · 12-02-2003, 02:11 AM

Stripping out threads hu? HEHHEHE thats the reason why I am swapping this out. This whole thing started with a points to hei conversion.

jorgensensc · 12-02-2003, 02:11 AM

That's a good idea Cat Fuzz!!! Shoulda thought about that before!

Longhorn Man · 12-02-2003, 02:13 AM

You seen these intake gaskets? http://67-72chevytrucks.com/vboard/s...threadid=21908

Cat Fuzz · 12-02-2003, 02:14 AM

Just looked and this will be my 100th post. Stay tuned for new avatar.

12-02-2003, 01:46 AM	#1
skokie Registered User Join Date: Oct 2003 Location: San Jose Ca. Posts: 3,354	Intake Manifold Gasket Does anyone know the part number for the fel pro intake manifold gasket for a 350? Going to be using a edelbrock 2101 performer. Thanks

12-02-2003, 02:05 AM	#4
skokie Registered User Join Date: Oct 2003 Location: San Jose Ca. Posts: 3,354	Yep it does. With any luck the manifold will be coming off either thursday or friday. Getting everything outta the way first and I have to wait for the adapter for my carb to arrive. Heres some pics of the manifold. Cant wait to drop this thing on there. Attached Images

12-02-2003, 02:05 AM	#5
skokie Registered User Join Date: Oct 2003 Location: San Jose Ca. Posts: 3,354	#2 Attached Images

12-02-2003, 02:06 AM	#6
skokie Registered User Join Date: Oct 2003 Location: San Jose Ca. Posts: 3,354	#3 Attached Images

12-02-2003, 02:11 AM	#9
jorgensensc Registered User Join Date: Jul 2003 Location: Cypress, Tx Posts: 4,005	That's a good idea Cat Fuzz!!! Shoulda thought about that before! __________________ 1972 C20 Suburban- Big Blue Betty '56 Chevy Bel Air Sedan- Frame up Restoration -What would you attempt to achieve if you knew you could not fail?- -I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door- R.I.P. EAST SIDE LOW LIFE

12-02-2003, 01:52 AM	#2
Cat Fuzz My son, my joy. Join Date: Sep 2003 Location: Spokane WA Posts: 463	MS90314

12-02-2003, 02:03 AM	#3
jorgensensc Registered User Join Date: Jul 2003 Location: Cypress, Tx Posts: 4,005	Mine was a 1205(pretty sure) performance gasket for an edelbrock rpm air gap. I highly suggest buying a good gasket and using the copper rtv sealant. You don't want to have to do this more than once!! Don't use the cork end pieces, just run a 1/4" bead on the ends. For best adhesion Put the sealant, (not on the ends), then the gaskets, torque down the manifold. Let it dry overnight. Remove the intake the next day. Check for gasket slippage and clean the gasket sealer off of the ports. Add sealant to ends, then put manifold back on and torque to specs. I did it this way and have had no leaks thusfar. Good luck and I hope this helps a little. __________________ 1972 C20 Suburban- Big Blue Betty '56 Chevy Bel Air Sedan- Frame up Restoration -What would you attempt to achieve if you knew you could not fail?- -I Refuse To Tiptoe Through Life, Only To Arrive Safely At Death's Door- R.I.P. EAST SIDE LOW LIFE

12-02-2003, 02:10 AM	#7
Cat Fuzz My son, my joy. Join Date: Sep 2003 Location: Spokane WA Posts: 463	I don't know if anyone else does this, but when I installed my Edelbrock Performer, I used studs and nuts for everything. That way when you go to change the thermostat or something, there is less risk of stripping out the threads.

12-02-2003, 02:13 AM	#10
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,690	You seen these intake gaskets? http://67-72chevytrucks.com/vboard/s...threadid=21908

12-02-2003, 02:14 AM	#11
Cat Fuzz My son, my joy. Join Date: Sep 2003 Location: Spokane WA Posts: 463	Just looked and this will be my 100th post. Stay tuned for new avatar.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.