71K-10 ignition Coil location - The 1947 - Present Chevrolet & GMC Truck Message Board Network

54blackhornet · 08-19-2013, 03:00 PM

Can anyone post a photo of the original coil mount location, trying to rewire mine back to stock. Was it mounted on intake or on firewall, it's a 350 4sp.

Thanks Guy's
Posted via Mobile Device

**kwmech** · 08-19-2013, 03:03 PM

Do you have the bracket that clamps the coil? It bolts to the intake behind the carb next to the dist. If you have the bracket it will line up on the intake holes with 5/16 by 3/4'' bolts

54blackhornet · 08-19-2013, 05:07 PM

It has a Edelbrock Performer intake on it ? Right now it is hanging off the firewall ?
Posted via Mobile Device

**TBONE1964** · 08-19-2013, 05:24 PM

The correct coil bracket looks like the one in the photo. The coil will stand almost straight up with a slight lean.

I don't recall if Edelbrock intakes have the correct hole locations. I think some do and some don't. You should see two 5/16 x 18 holes tapped into bosses between the carb and the distributor.

This information is for the factory configuration.

mrein3 · 08-19-2013, 10:25 PM

Quote:

Originally Posted by 54blackhornet

Can anyone post a photo of the original coil mount location, trying to rewire mine back to stock. Was it mounted on intake or on firewall, it's a 350 4sp.

Thanks Guy's
Posted via Mobile Device

Not a truck but its a 1972 Chevelle with a stock points type coil and distributor. I'm 99.9997% sure it the same on our trucks. I took my coil off my truck years ago and replaced it with a HEI setup. Looking at the date code on those plug wires and knowing when I rebuilt that engine I'd say that coil was bolted down there in 1989. In 1989 I would have had no idea you could replace that ignition with a HEI. Even though I managed to rebuild that 350 myself.

**TBONE1964** · 08-19-2013, 11:50 PM

Quote:

Originally Posted by mrein3

Not a truck but its a 1972 Chevelle with a stock points type coil and distributor. I'm 99.9997% sure it the same on our trucks. I took my coil off my truck years ago and replaced it with a HEI setup. Looking at the date code on those plug wires and knowing when I rebuilt that engine I'd say that coil was bolted down there in 1989. In 1989 I would have had no idea you could replace that ignition with a HEI. Even though I managed to rebuild that 350 myself.

^2 I agree

08-19-2013, 03:00 PM	#1
54blackhornet Registered User Join Date: Jul 2008 Location: Eastern Oregon Posts: 2,391	71K-10 ignition Coil location Can anyone post a photo of the original coil mount location, trying to rewire mine back to stock. Was it mounted on intake or on firewall, it's a 350 4sp. Thanks Guy's Posted via Mobile Device __________________ 71 C-20 07 Magnum RT AWD

08-19-2013, 03:03 PM	#2
kwmech Senior Member Join Date: Mar 2003 Location: Colfax-California Posts: 8,630	Re: 71K-10 ignition Coil location Do you have the bracket that clamps the coil? It bolts to the intake behind the carb next to the dist. If you have the bracket it will line up on the intake holes with 5/16 by 3/4'' bolts

08-19-2013, 05:07 PM	#3
54blackhornet Registered User Join Date: Jul 2008 Location: Eastern Oregon Posts: 2,391	Re: 71K-10 ignition Coil location It has a Edelbrock Performer intake on it ? Right now it is hanging off the firewall ? Posted via Mobile Device __________________ 71 C-20 07 Magnum RT AWD

08-19-2013, 05:24 PM	#4
TBONE1964 Cluster King Join Date: Nov 2012 Location: Junction City, OR Posts: 5,263	Re: 71K-10 ignition Coil location The correct coil bracket looks like the one in the photo. The coil will stand almost straight up with a slight lean. I don't recall if Edelbrock intakes have the correct hole locations. I think some do and some don't. You should see two 5/16 x 18 holes tapped into bosses between the carb and the distributor. This information is for the factory configuration. Attached Images



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.