1967 Mustang Coupe Build (Electra) - Page 14 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

shearjs · 10-14-2013, 10:55 AM

You've got that thing looking good!

JRANGER · 10-14-2013, 11:10 AM

Quote:

Originally Posted by shearjs

You've got that thing looking good!

Thanks Jason!! Wish it was looking as good as that truck of yours

JRANGER · 10-20-2013, 11:41 AM

Well started taking things apart to replace the thermostat only to find that the housing was jacked up. It was so rusted and nasty I had to replace it as well as the water pump hose..So new 180 degree thermostat, new housing, new gasket. and new permatex, So far so good i drove it for about 10 minutes and let it idle for about 25 and it never even made it to halfway on the temperature gauge. It kinda cold though so im not certain its fixed, just need to take it for a drive sometime soon and see how she does. Only thing is its leaking out of the temp sending unit screw that on the new housing..I should of rethought it and put Teflon tape on it but i wasn't thinking about it. Ill do that here soon, its barely leaking

screamin_c10 · 10-21-2013, 04:06 AM

Hell that one is in great shape... check out the one I pulled off the Cougars 289...

JRANGER · 10-26-2013, 11:50 PM

Took the mustang for a drive to see if the new thermostat did any good. The car did great and didnt even come close to over heating. So when i finally got back home around 4 I went to work on what I thought was going to be a quick install. A new export brace and Monte Carlo bar. Needless to say it took several hours to tweak the export brace in place. The Monte Carlo bar was a little hard but not big deal. I still have to drive for the top holes but it was time to call it a night.

67ChevyRedneck · 10-27-2013, 12:52 AM

It sucks you already did it, but I've been told by quite a few people a trick for making the export brace fit (if it doesn't) is to let the car sit on jackstands over night (place them near the firewall on each side), and it should let the car settle enough over night to get the bolts started. I have one I bought months ago, but I want to pull my valve covers and repaint them before I install it. They're already hard enough to get off with the A/C and heater hose crap everywhere.

Did you add the extra brace on the firewall? (I don't see it in your pic).

http://forums.vintage-mustang.com/vi...ort-brace.html

JRANGER · 10-27-2013, 12:58 AM

I read about that but I have a slightly slanted driveway I wouldn't trust to do so. I didn't add an extra firewall brace. Is it needed?

67ChevyRedneck · 10-27-2013, 11:00 AM

I don't know. From thread above they look like they don't fit very well either... It supposedly keeps the firewall from getting fatigue cracks... but there isn't anything there with the other braces... so... ??? I have one, but I haven't checked it for fit. To be honest, I went out in the garage after reading that thread (mine came from NPD too) to check the fit and I couldn't find the damn thing

I think I asked this already, but are you planning on going to the big 50th show in Charlotte in April?

JRANGER · 10-27-2013, 11:33 AM

I am not planning as of right now. I have to see how the mustang comes a long at this point. Just trying to take it a day at a time. The brace is def hit and miss. I read a bunch of threads about its a hit and miss pain in the butt. So o well, my car is a pain in the butt! LOL

Drilled a few holes and Finished installing the Monte Carlo bar this morning

**Dieselwrencher** · 10-28-2013, 03:12 PM

I'm curious, what is the MonteCarlo bar supposed to do? When we do my Mom's 68 I'm planning on welding in subframe connectors to help stiffen the car up. Is the MonteCarlo bar just giving the fender wells more strength in the spring pocket areas?

JRANGER · 10-28-2013, 03:14 PM

Quote:

Originally Posted by Dieselwrencher

I'm curious, what is the MonteCarlo bar supposed to do? When we do my Mom's 68 I'm planning on welding in subframe connectors to help stiffen the car up. Is the MonteCarlo bar just giving the fender wells more strength in the spring pocket areas?

The Monte Carlo bar and the upgraded Export brace are suppose stiffen up the suspension and help prevent shock tower flex especially on cornering. Alot of people have said there is a noticeable difference with installing these setup

From CJPONYPARTS "tubular bar ties the inner fenders together across the front of the shock towers to reduce chassis flex. Helps improve body rigidity for better handling"
" export brace will strengthen the front end and help reduce shock tower fatigue and cracking"

67ChevyRedneck · 10-28-2013, 03:16 PM

It's just to provide more lateral stiffness. There can still be some movement with the export brace. Most would argue that unless you're racing your car and throwing it into corners, the monte carlo bar is unnecessary, the export bar stiffens the car up enough for regular driving, but there are benefits to having both.

JRANGER · 11-03-2013, 12:02 AM

Didnt get as much done as I had hoped today but I did get the holes in the rear window frame welded shut and put some bondo on it to smooth and fill a bit.

I also welded one of the bolts in on the export brace on the shock tower. The bolt was spinning and i had enough room to feed wire under it and weld it in. Now its nice and tight.

After putting in the new bolt to the firewall portion of the export brace it tightened and made all the other bolts loose. So I ended up having to use 2 new bolts and 2 old bolts. (New ones are slightly smaller so i didnt want to use all 4.

Also installed my mini tach and took her for a drive.

Next week I hope to get her disassembled and get started on sanding her smooth for paint

Rusbuilt · 11-03-2013, 07:41 AM

What... No pictures? lol

JRANGER · 11-03-2013, 12:18 PM

LOL....I know right but i figured do more take less pics....plus its just pics of bondo and a mini tach....

Removed the bumpers this morning.

Investigated the steering noise and its very close to the ball joint but i see no wear or signs of grinding. So i have no clue as to why i get knocking when turning left. Maybe it has something to do with the frame rail just not certain

JRANGER · 11-03-2013, 12:40 PM

hmmm, checked into this and people with the same problem suggest checking the wheel bearing. Guess that could be it...

JRANGER · 11-09-2013, 07:48 PM

Sanding....LOTS of sanding.... I have found bondo from the previous owner but its not a lot. It seems to be all on pitting spots so nothing major as of yet

cubber · 11-10-2013, 05:38 PM

That blitz black is gonna be SWEET!

JRANGER · 11-10-2013, 07:32 PM

haha, yes sir!!!

JRANGER · 11-11-2013, 08:51 PM

Well a lot more sanding has been done.

Removed the front windshield and discovered a big hole. So welded i shut and did some grinding on it. Also noticed that both Pillars had been replaced at some point...craziness

The whole car got its initial sanding completed other then hand sanding areas like the headlight areas and such. Car has skim coats over all the needed areas.

Now to sand the bondo in a few days and get those other areas.......PAINT SOON MUHAHAHAH

**Denee007** · 11-11-2013, 09:43 PM

That's starting to take shape! Looks like a Mustang for sure!

cubber · 11-12-2013, 12:42 AM

Man, I'd cover those wheels and tires asap!

JRANGER · 11-12-2013, 12:45 AM

hahaah! Its just dust but they will be covered soon

cubber · 11-12-2013, 12:47 AM

I know, but if your luck is like mine, you better be REAL careful, lol. The sanding looks well done, though!

JRANGER · 11-12-2013, 12:48 AM

haha gotcha...Id hope so, i went through over 100 sanding discs lol

10-14-2013, 10:55 AM	#326
shearjs Registered User Join Date: Mar 2011 Location: Thompsons Station, TN Posts: 700	Re: 1967 Mustang Coupe Build (Electra) You've got that thing looking good! __________________ -Jason '72 Family Hauler Rufus' Restoration - 70 GMC, LS swap - SOLD

10-20-2013, 11:41 AM	#328
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) Well started taking things apart to replace the thermostat only to find that the housing was jacked up. It was so rusted and nasty I had to replace it as well as the water pump hose..So new 180 degree thermostat, new housing, new gasket. and new permatex, So far so good i drove it for about 10 minutes and let it idle for about 25 and it never even made it to halfway on the temperature gauge. It kinda cold though so im not certain its fixed, just need to take it for a drive sometime soon and see how she does. Only thing is its leaking out of the temp sending unit screw that on the new housing..I should of rethought it and put Teflon tape on it but i wasn't thinking about it. Ill do that here soon, its barely leaking Attached Images __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

10-21-2013, 04:06 AM	#329
screamin_c10 I dun gradjiated collij!!! Join Date: Jan 2006 Location: St. Helens Oregon Posts: 1,751	Re: 1967 Mustang Coupe Build (Electra) Hell that one is in great shape... check out the one I pulled off the Cougars 289... Attached Images __________________ Built NOT Bought. Viper Red 1971 LWB C10 355 Vortec W/700R4 4/5 drop AKA Screamin' You are missed! 2006 F150 XLT 5.4L Triton Rollin' on 22s the "F1" 67 C20 PS/AC/327/TH400 we call 'er "Bessie" 67 Malibu PS/ZR1-LS1 Brakes/350 Vortec/700R4 2/2 drop on 18" 338s - Tracy's "Boo" Boosted '67 Cougar EFI 5.0 HO roller motor/T5/8.8 Tracloc/ 4 wheel disks - "Project Panther" 79 Honda Z50 - stretched, cafe'd and hotrodded 125CC Lifan/5spd FEAR THE MONKEY!

10-26-2013, 11:50 PM	#330
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) Took the mustang for a drive to see if the new thermostat did any good. The car did great and didnt even come close to over heating. So when i finally got back home around 4 I went to work on what I thought was going to be a quick install. A new export brace and Monte Carlo bar. Needless to say it took several hours to tweak the export brace in place. The Monte Carlo bar was a little hard but not big deal. I still have to drive for the top holes but it was time to call it a night. Attached Images __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

10-27-2013, 12:52 AM	#331
67ChevyRedneck Hittin E-Z Street on Mud Tires Join Date: Nov 2004 Location: Greenville, SC Posts: 23,090	Re: 1967 Mustang Coupe Build (Electra) It sucks you already did it, but I've been told by quite a few people a trick for making the export brace fit (if it doesn't) is to let the car sit on jackstands over night (place them near the firewall on each side), and it should let the car settle enough over night to get the bolts started. I have one I bought months ago, but I want to pull my valve covers and repaint them before I install it. They're already hard enough to get off with the A/C and heater hose crap everywhere. Did you add the extra brace on the firewall? (I don't see it in your pic). http://forums.vintage-mustang.com/vi...ort-brace.html __________________ Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications!

10-27-2013, 12:58 AM	#332
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) I read about that but I have a slightly slanted driveway I wouldn't trust to do so. I didn't add an extra firewall brace. Is it needed? __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

10-27-2013, 11:00 AM	#333
67ChevyRedneck Hittin E-Z Street on Mud Tires Join Date: Nov 2004 Location: Greenville, SC Posts: 23,090	Re: 1967 Mustang Coupe Build (Electra) I don't know. From thread above they look like they don't fit very well either... It supposedly keeps the firewall from getting fatigue cracks... but there isn't anything there with the other braces... so... ??? I have one, but I haven't checked it for fit. To be honest, I went out in the garage after reading that thread (mine came from NPD too) to check the fit and I couldn't find the damn thing I think I asked this already, but are you planning on going to the big 50th show in Charlotte in April? __________________ Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications!

10-27-2013, 11:33 AM	#334
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) I am not planning as of right now. I have to see how the mustang comes a long at this point. Just trying to take it a day at a time. The brace is def hit and miss. I read a bunch of threads about its a hit and miss pain in the butt. So o well, my car is a pain in the butt! LOL Drilled a few holes and Finished installing the Monte Carlo bar this morning __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

10-28-2013, 03:12 PM	#335
Dieselwrencher 6>8 Plugless........ Join Date: Sep 2007 Location: Prairie City, Ia Posts: 17,142	Re: 1967 Mustang Coupe Build (Electra) I'm curious, what is the MonteCarlo bar supposed to do? When we do my Mom's 68 I'm planning on welding in subframe connectors to help stiffen the car up. Is the MonteCarlo bar just giving the fender wells more strength in the spring pocket areas? __________________ Ryan 1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread 1972 GMC Sierra Grande Longhorn 4x4 1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed 1972 C10 Suburban Custom Deluxe 1969 Chevy milk truck 1971 Camaro RS 5.3 BTR STG3 Cam Super T10 1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project *Tired of spark plugs? Check this out.*

10-28-2013, 03:16 PM	#337
67ChevyRedneck Hittin E-Z Street on Mud Tires Join Date: Nov 2004 Location: Greenville, SC Posts: 23,090	Re: 1967 Mustang Coupe Build (Electra) It's just to provide more lateral stiffness. There can still be some movement with the export brace. Most would argue that unless you're racing your car and throwing it into corners, the monte carlo bar is unnecessary, the export bar stiffens the car up enough for regular driving, but there are benefits to having both. __________________ Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications!

11-03-2013, 12:02 AM	#338
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) Didnt get as much done as I had hoped today but I did get the holes in the rear window frame welded shut and put some bondo on it to smooth and fill a bit. I also welded one of the bolts in on the export brace on the shock tower. The bolt was spinning and i had enough room to feed wire under it and weld it in. Now its nice and tight. After putting in the new bolt to the firewall portion of the export brace it tightened and made all the other bolts loose. So I ended up having to use 2 new bolts and 2 old bolts. (New ones are slightly smaller so i didnt want to use all 4. Also installed my mini tach and took her for a drive. Next week I hope to get her disassembled and get started on sanding her smooth for paint __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

11-03-2013, 07:41 AM	#339
Rusbuilt Registered User Join Date: Mar 2012 Location: Knoxville, TN Posts: 5,381	Re: 1967 Mustang Coupe Build (Electra) What... No pictures? lol __________________ -Rus PLEASE HELP WITH PROJECT UNDERHAULINPaypal donations accepted @ rus1785@yahoo.com Rusbuilt's garage 1968 Chevy C-30 Darcy SOLD Rusbuilt shop truck *SOLD*

11-03-2013, 12:18 PM	#340
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) LOL....I know right but i figured do more take less pics....plus its just pics of bondo and a mini tach.... Removed the bumpers this morning. Investigated the steering noise and its very close to the ball joint but i see no wear or signs of grinding. So i have no clue as to why i get knocking when turning left. Maybe it has something to do with the frame rail just not certain __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

11-03-2013, 12:40 PM	#341
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) hmmm, checked into this and people with the same problem suggest checking the wheel bearing. Guess that could be it... __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

11-09-2013, 07:48 PM	#342
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) Sanding....LOTS of sanding.... I have found bondo from the previous owner but its not a lot. It seems to be all on pitting spots so nothing major as of yet Attached Images __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper



Register or Log In To remove these advertisements.

11-10-2013, 05:38 PM	#343
cubber Registered User Join Date: Mar 2012 Location: Leanna, TN Posts: 2,061	Re: 1967 Mustang Coupe Build (Electra) That blitz black is gonna be SWEET! __________________ =MATTHEW 69 Stepper...Stroked & Bagged GONE BUT NOT FORGOTTEN 2003 Chevrolet Z71 Ext. Cab 1995 Cavalier gas saver!

11-10-2013, 07:32 PM	#344
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) haha, yes sir!!! __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

11-11-2013, 08:51 PM	#345
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) Well a lot more sanding has been done. Removed the front windshield and discovered a big hole. So welded i shut and did some grinding on it. Also noticed that both Pillars had been replaced at some point...craziness The whole car got its initial sanding completed other then hand sanding areas like the headlight areas and such. Car has skim coats over all the needed areas. Now to sand the bondo in a few days and get those other areas.......PAINT SOON MUHAHAHAH Attached Images __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

11-11-2013, 09:43 PM	#346
Denee007 Senior Member Join Date: May 2011 Location: Cypress, Tx. Posts: 1,504	Re: 1967 Mustang Coupe Build (Electra) That's starting to take shape! Looks like a Mustang for sure! __________________ '72 Ford Bronco project(July 17 2021-?) https://67-72chevytrucks.com/vboard/...d.php?t=828015 59 Apache (sold 6-25-2021) 67 Ford Mustang (re-restored after Harvey) 1968 Jeep Cj5 (2-8-2020 to present) 1992 Jeep Yj (8-17-20 to present) (Jurassic build) www.Classiccarsandtools.com

11-12-2013, 12:42 AM	#347
cubber Registered User Join Date: Mar 2012 Location: Leanna, TN Posts: 2,061	Re: 1967 Mustang Coupe Build (Electra) Man, I'd cover those wheels and tires asap! __________________ =MATTHEW 69 Stepper...Stroked & Bagged GONE BUT NOT FORGOTTEN 2003 Chevrolet Z71 Ext. Cab 1995 Cavalier gas saver!

11-12-2013, 12:45 AM	#348
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) hahaah! Its just dust but they will be covered soon __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

11-12-2013, 12:47 AM	#349
cubber Registered User Join Date: Mar 2012 Location: Leanna, TN Posts: 2,061	Re: 1967 Mustang Coupe Build (Electra) I know, but if your luck is like mine, you better be REAL careful, lol. The sanding looks well done, though! __________________ =MATTHEW 69 Stepper...Stroked & Bagged GONE BUT NOT FORGOTTEN 2003 Chevrolet Z71 Ext. Cab 1995 Cavalier gas saver!

11-12-2013, 12:48 AM	#350
JRANGER Registered User Join Date: Nov 2011 Location: Nashville TN Posts: 3,595	Re: 1967 Mustang Coupe Build (Electra) haha gotcha...Id hope so, i went through over 100 sanding discs lol __________________ PLEASE HELP WITH PROJECT UNDERHAULIN http://67-72chevytrucks.com/vboard/showthread.php?t=306320 Gemini - 1978 GMC C15 High Sierra - 305 c/e - Given to Mother Electra - 1967 Mustang Coupe - 302/w 3 speed Build Chyna - 1968 Chevy C20 Long Stepper

Register or Log In To remove these advertisements.