![]() |
![]() |
#1 |
Registered User
Join Date: Oct 2013
Location: Huntington Beach, California
Posts: 18
|
Emblem loose?
my emblem is wiggly on my truck. its annoying and it bothers me. is it supposed to wiggle? the speed nut/ clips on the back are tight. am i missing something? thanks
__________________
1970 c20 cst 350/400 14bolt rear Last edited by ChevykidHB; 11-05-2013 at 01:32 AM. |
![]() |
![]() |
![]() |
#2 |
Senior Member
![]() Join Date: Feb 2011
Location: Clovis Ca.
Posts: 632
|
Re: Emblem loose?
The speed nut might be bottoming out, or getting tight before it tightening up the emblem. Try putting a washer or two between the inside of the fender and the speed nut.
__________________
I'm sorry I called you stupid. I thought you knew already. 67 C-20 Custom Camper 68 Nova 396 it does wheelies 2005 Buick Century the one the wife drives 1989 Toyota Tercel to drive when I can't put gas in the first 2. |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Oct 2013
Location: Huntington Beach, California
Posts: 18
|
Re: Emblem loose?
Thats what i thought at first but the emblem is all the way on it just tilts back and forth over the two pegs
__________________
1970 c20 cst 350/400 14bolt rear |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Oct 2013
Location: Huntington Beach, California
Posts: 18
|
Re: Emblem loose?
i take that back. i diddnt use speed nuts i used those push on rings. i dont know if theres a difference they are smaller than the speed nut that came off it.
__________________
1970 c20 cst 350/400 14bolt rear |
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: Emblem loose?
get new better fasteners lowes home depot ace hardware are a few places to get them
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
![]() |
![]() |
![]() |
#6 |
The Older Generation
![]() ![]() ![]() Join Date: Aug 2006
Location: Montezuma, Iowa
Posts: 26,058
|
Re: Emblem loose?
-
Cut a small circle out of a piece of flat rubber about 3/32nds or 1/8 of an inch thick and slide over the posts before you put the fasteners on. Worked for me. LockDoc
__________________
Leon Locksmith, Specializing In Antique Trucks, Automobiles, & Motorcycles (My Dually Pickup Project Thread) http://67-72chevytrucks.com/vboard/s...d.php?t=829820 - |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Oct 2013
Location: Huntington Beach, California
Posts: 18
|
Re: Emblem loose?
Dang. I used te push on fasteners and they are hard to get off... Any tips on getting them off. Any tips to get em off without doing damage?
__________________
1970 c20 cst 350/400 14bolt rear |
![]() |
![]() |
![]() |
Bookmarks |
|
|