Project "Man Pedal" - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**JIMs70GMC** · 11-01-2014, 07:45 PM

I figured I'd start a project thread for my manual tranny swap in my 86 K5. I'll get some pics this weekend. I believe I have all the parts collected to begin. Once I sell the 700r4/208 combo I will drop them.

I originally found a 1971 SM465/NP205 combo and bought the pedals and bell housing/hydro clutch from board members. Going to use them but I found another SM465/NP205 combo from an 1984 and will use them vice the 71 parts. I will be able to use my front driveshaft from the 700R4/208 but will need to fabricate one for the rear.

I am hoping to find some 8-lug axles(3/4 ton) before this is done so I can swap them in too.

Other plans:
-Raptor line the inside (interior is removed)
-new exhaust with ram horns purchased from a board member (currently has headers that prevent installing front drive shaft)
-has a small amount of lift via add-a-leafs front and rear (might replace with lift springs)

**JIMs70GMC** · 11-05-2014, 10:43 PM

My first update, sold the 700r4/208 combo. Dropping them this Saturday. Then I'll start putting her back together.

**JIMs70GMC** · 11-07-2014, 09:44 PM

Got the headers off today. Tranny/TC will be gone tomorrow.

**JIMs70GMC** · 11-08-2014, 08:06 PM

700r4 and np208 removed.

**JIMs70GMC** · 11-08-2014, 08:07 PM

1971 SM465 and NP205 I was going to use. The 1984 SM465 is in the background as is the 1987 bell housing I am going to use.

**JIMs70GMC** · 11-08-2014, 08:10 PM

The 1984 SM465 and 1984 NP205. Tomorrow I am going to remove the old pedal assembly and mark the firewall to mount the master cylinder and reservoir. I also need to look into cross members, not sure if the auto cross member will work, looks like it does not drop down in the center far enough.

19silverado77 · 11-09-2014, 06:33 AM

Your cross member may work I swapped a 68 465 into my 77 and it worked so I suppose it should.

**JIMs70GMC** · 11-09-2014, 07:26 PM

I have the 71's cross member, I will try it too.

**JIMs70GMC** · 11-10-2014, 10:17 PM

Looks like I need a pre 85 cross member to work with my 84 SM465/NP205. The nice thing is I found one locally on craigslist. Going to get it tomorrow!

**JIMs70GMC** · 11-16-2014, 06:43 PM

I went to pick-up the cross member I found and come to find out the truck he was parting out was an 86, not an 84. Oh well, still looking for a pre 85 cross member.

**argonaut** · 11-17-2014, 01:24 AM

Looks like you're making good progress. I must say I'm a little surprised to see you swapping an overdrive trans with a non-overdrive unit. What motivated the auto to manual swap?

**JIMs70GMC** · 11-30-2014, 08:12 PM

Quote:

Originally Posted by argonaut

Looks like you're making good progress. I must say I'm a little surprised to see you swapping an overdrive trans with a non-overdrive unit. What motivated the auto to manual swap?

I have always enjoyed driving the manual trannys. This vehicle is more for fun, I have a Tahoe I drive for day to day stuff.

No update, but I have everything I need to install the 465/205 into my K5. Might be another week since the clutch went out in my K25 and I want to get it back on the road first.

**JIMs70GMC** · 12-08-2014, 08:58 AM

Well. My K25 clutch issue was not the clutch. Turns out the power sleeve splines were all stripped out. Ordered a new one on ebay. Also, the last few odd and ends are coming in, tranny hump and shifter for the K5. Probably replace the power sleeve in that one too.

**JIMs70GMC** · 12-26-2014, 07:03 PM

Lots of progress today. The tranny is in! Also, have the adapter bolted to the transmission and the cross member installed. No more jack-stand holding up the engine!

Going to swap pedal assemblies and install the clutch master cylinder tomorrow. The slave cylinder needs to be replaced or rebuilt too.

Also going to install the ramhorns and looks like a custom dual exhaust or maybe a heartthrob exhaust. Not sure yet.

**JIMs70GMC** · 12-27-2014, 07:55 PM

Started to remove the pedal assembly and drill the holes. Also mounted my "new" exhaust manifolds. You can see the dimples on the firewall next to the brake booster where the clutch master cylinder mounts.

**JIMs70GMC** · 12-27-2014, 07:57 PM

manifolds and tranny installed:

**JIMs70GMC** · 01-19-2015, 08:17 PM

Started prepping for pedals.

**JIMs70GMC** · 01-19-2015, 08:20 PM

Couple more.

**JIMs70GMC** · 01-24-2015, 09:49 PM

Got the steering column out of the way. Easier than I thought. Also, started putting the pedal assembly in. Here's a couple update pics.

**JIMs70GMC** · 01-25-2015, 09:04 PM

I got the steering column in.

**argonaut** · 01-25-2015, 09:35 PM

Nice progress! Real men drive stick!

**JIMs70GMC** · 01-25-2015, 10:59 PM

Thanks Jason. Before I put the gauges back in I need to make sure I have the clutch pedal attached to the master cylinder correctly. Looking for some pics/info now.

**JIMs70GMC** · 02-12-2015, 01:22 PM

Quick update. I should be all done by March 1st. I have ordered an exhaust kit and the drive shafts are at the driveline shop now. Worked out my clutch hook-up issue and the interior is almost all back together.

**argonaut** · 02-13-2015, 10:29 AM

Awesome! You must be excited to drive it.

**JIMs70GMC** · 02-13-2015, 10:17 PM

I am, this has been 2 months longer than I planned.

11-01-2014, 07:45 PM	#1
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Project "Man Pedal" I figured I'd start a project thread for my manual tranny swap in my 86 K5. I'll get some pics this weekend. I believe I have all the parts collected to begin. Once I sell the 700r4/208 combo I will drop them. I originally found a 1971 SM465/NP205 combo and bought the pedals and bell housing/hydro clutch from board members. Going to use them but I found another SM465/NP205 combo from an 1984 and will use them vice the 71 parts. I will be able to use my front driveshaft from the 700R4/208 but will need to fabricate one for the rear. I am hoping to find some 8-lug axles(3/4 ton) before this is done so I can swap them in too. Other plans: -Raptor line the inside (interior is removed) -new exhaust with ram horns purchased from a board member (currently has headers that prevent installing front drive shaft) -has a small amount of lift via add-a-leafs front and rear (might replace with lift springs) __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

11-05-2014, 10:43 PM	#2
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" My first update, sold the 700r4/208 combo. Dropping them this Saturday. Then I'll start putting her back together. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

11-07-2014, 09:44 PM	#3
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" Got the headers off today. Tranny/TC will be gone tomorrow. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

11-08-2014, 08:06 PM	#4
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" 700r4 and np208 removed. Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

11-08-2014, 08:07 PM	#5
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" 1971 SM465 and NP205 I was going to use. The 1984 SM465 is in the background as is the 1987 bell housing I am going to use. Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

11-08-2014, 08:10 PM	#6
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" The 1984 SM465 and 1984 NP205. Tomorrow I am going to remove the old pedal assembly and mark the firewall to mount the master cylinder and reservoir. I also need to look into cross members, not sure if the auto cross member will work, looks like it does not drop down in the center far enough. Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

11-09-2014, 06:33 AM	#7
19silverado77 Registered User Join Date: Nov 2013 Location: Tucson, Arizona Posts: 167	Re: Project "Man Pedal" Your cross member may work I swapped a 68 465 into my 77 and it worked so I suppose it should.

11-09-2014, 07:26 PM	#8
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" I have the 71's cross member, I will try it too. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

11-10-2014, 10:17 PM	#9
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" Looks like I need a pre 85 cross member to work with my 84 SM465/NP205. The nice thing is I found one locally on craigslist. Going to get it tomorrow! __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

11-16-2014, 06:43 PM	#10
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" I went to pick-up the cross member I found and come to find out the truck he was parting out was an 86, not an 84. Oh well, still looking for a pre 85 cross member. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm Last edited by JIMs70GMC; 11-17-2014 at 02:13 PM.

11-17-2014, 01:24 AM	#11
argonaut Senior Member Join Date: Aug 2008 Location: Long Beach, CA Posts: 1,813	Re: Project "Man Pedal" Looks like you're making good progress. I must say I'm a little surprised to see you swapping an overdrive trans with a non-overdrive unit. What motivated the auto to manual swap? __________________ Jason M. @argonaut62 1972 K5 Blazer CST, Turquoise 1966 K20 Short Fleet Pickup, Big Ugly 1964 C10 Short Fleet, Gertrude 2001 Porsche 911 Carrera 1996 Ford Bronco XLT 1980 Jeep Wagoneer 2008 Honda CBR1000RR 2005 Honda RC51 1981 Honda CB750C No dis-assemble Johnny Five! No dis-assemble!

12-08-2014, 08:58 AM	#13
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" Well. My K25 clutch issue was not the clutch. Turns out the power sleeve splines were all stripped out. Ordered a new one on ebay. Also, the last few odd and ends are coming in, tranny hump and shifter for the K5. Probably replace the power sleeve in that one too. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

12-26-2014, 07:03 PM	#14
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" Lots of progress today. The tranny is in! Also, have the adapter bolted to the transmission and the cross member installed. No more jack-stand holding up the engine! Going to swap pedal assemblies and install the clutch master cylinder tomorrow. The slave cylinder needs to be replaced or rebuilt too. Also going to install the ramhorns and looks like a custom dual exhaust or maybe a heartthrob exhaust. Not sure yet. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

12-27-2014, 07:55 PM	#15
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" Started to remove the pedal assembly and drill the holes. Also mounted my "new" exhaust manifolds. You can see the dimples on the firewall next to the brake booster where the clutch master cylinder mounts. Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

12-27-2014, 07:57 PM	#16
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" manifolds and tranny installed: Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm



Register or Log In To remove these advertisements.

01-19-2015, 08:17 PM	#17
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" Started prepping for pedals. Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

01-19-2015, 08:20 PM	#18
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" Couple more. Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

01-24-2015, 09:49 PM	#19
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" Got the steering column out of the way. Easier than I thought. Also, started putting the pedal assembly in. Here's a couple update pics. Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

01-25-2015, 09:04 PM	#20
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" I got the steering column in. Attached Images __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

01-25-2015, 09:35 PM	#21
argonaut Senior Member Join Date: Aug 2008 Location: Long Beach, CA Posts: 1,813	Re: Project "Man Pedal" Nice progress! Real men drive stick! __________________ Jason M. @argonaut62 1972 K5 Blazer CST, Turquoise 1966 K20 Short Fleet Pickup, Big Ugly 1964 C10 Short Fleet, Gertrude 2001 Porsche 911 Carrera 1996 Ford Bronco XLT 1980 Jeep Wagoneer 2008 Honda CBR1000RR 2005 Honda RC51 1981 Honda CB750C No dis-assemble Johnny Five! No dis-assemble!

01-25-2015, 10:59 PM	#22
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" Thanks Jason. Before I put the gauges back in I need to make sure I have the clutch pedal attached to the master cylinder correctly. Looking for some pics/info now. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

02-12-2015, 01:22 PM	#23
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" Quick update. I should be all done by March 1st. I have ordered an exhaust kit and the drive shafts are at the driveline shop now. Worked out my clutch hook-up issue and the interior is almost all back together. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

02-13-2015, 10:29 AM	#24
argonaut Senior Member Join Date: Aug 2008 Location: Long Beach, CA Posts: 1,813	Re: Project "Man Pedal" Awesome! You must be excited to drive it. __________________ Jason M. @argonaut62 1972 K5 Blazer CST, Turquoise 1966 K20 Short Fleet Pickup, Big Ugly 1964 C10 Short Fleet, Gertrude 2001 Porsche 911 Carrera 1996 Ford Bronco XLT 1980 Jeep Wagoneer 2008 Honda CBR1000RR 2005 Honda RC51 1981 Honda CB750C No dis-assemble Johnny Five! No dis-assemble!

02-13-2015, 10:17 PM	#25
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: Project "Man Pedal" I am, this has been 2 months longer than I planned. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

Register or Log In To remove these advertisements.