1967 gmc hubcap ID... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**too much stuff** · 12-28-2014, 11:21 PM

Trying to determine if these would be correct on my 67 gmc. They are aluminum, not steel. Any help or info is appreciated. I didn't pull the cap off yet, but can i assume these would be for a nub style wheel?

factorystock · 12-29-2014, 12:48 AM

Yes, those are correct for 1967 GMC. Your wheel appears to be the standard nub style that accepts the regular 10 1/4" cap. Many of those '67-'68 caps look the same from the outside, but the backs sides can be different if wheels are clip type. Those are not aluminum, they are chrome over brass. They are notorious for splitting on the edges, be careful when removing. Those should shine up again after a little scrubbing with a very wet SOS pad.

BLT gmc · 12-29-2014, 10:37 AM

This is the best site I have found for GMC cap ID. http://gmcguy.com/gmc_hubcaps_wheel_..._and_rims.html

Bruce

motorcritter · 12-29-2014, 03:40 PM

A good, cheap way to clean up chrome is aluminium foil and soda pop- I'm told that diet Pepsi is best, but they guy that told me drinks that exclusively. Rub the crumpled foil over the surface, using the soda as a wash/lube. Amazing results, especially if it's got specks of corrosion on it.

**too much stuff** · 12-30-2014, 10:35 PM

Quote:

Originally Posted by factorystock

Yes, those are correct for 1967 GMC. Your wheel appears to be the standard nub style that accepts the regular 10 1/4" cap. Many of those '67-'68 caps look the same from the outside, but the backs sides can be different if wheels are clip type. Those are not aluminum, they are chrome over brass. They are notorious for splitting on the edges, be careful when removing. Those should shine up again after a little scrubbing with a very wet SOS pad.

Thanks for the info. Thought it was aluminum when it matched the trim on the side and i put a magnet to it and it didn't stick. Also the hole in it made me think it wasn't steel. Too bad i only have the 2 and they aren't very nice.

Quote:

Originally Posted by BLT gmc

This is the best site I have found for GMC cap ID. http://gmcguy.com/gmc_hubcaps_wheel_..._and_rims.html

Bruce

Very informative. Thanks.

Quote:

Originally Posted by motorcritter

A good, cheap way to clean up chrome is aluminium foil and soda pop- I'm told that diet Pepsi is best, but they guy that told me drinks that exclusively. Rub the crumpled foil over the surface, using the soda as a wash/lube. Amazing results, especially if it's got specks of corrosion on it.

Thanks for the tip.

12-28-2014, 11:21 PM	#1
too much stuff Roadtrip! Join Date: Feb 2003 Location: Grand Rapids MN Posts: 13,787	1967 gmc hubcap ID... Trying to determine if these would be correct on my 67 gmc. They are aluminum, not steel. Any help or info is appreciated. I didn't pull the cap off yet, but can i assume these would be for a nub style wheel? Attached Images __________________ 67 gmc custom lwb dakota truck. Sold...And bought back 69 swb 4x4 project (in progress) 70 c-10 lwb texas truck 70 4x4/BB/bkts/posi/tach(retired) 70 swb (wifes) 70 jimmy camper 71 K-5 factory 2wd 71 cheyenne 4x4/tach/posi/ plow rig 71 Cheyenne20 BB, buckets, tach, tilt, 4 speed 72 jimmy CST wyoming rig 72 jimmy Colorado rig 72 lifted texas 4x4 3/4 ton burb 65 fury conv. 383/auto 65 chrysler 300 "L" 413 auto

12-29-2014, 12:48 AM	#2
factorystock Registered User Join Date: Feb 2007 Location: west coast Posts: 3,396	Re: 1967 gmc hubcap ID... Yes, those are correct for 1967 GMC. Your wheel appears to be the standard nub style that accepts the regular 10 1/4" cap. Many of those '67-'68 caps look the same from the outside, but the backs sides can be different if wheels are clip type. Those are not aluminum, they are chrome over brass. They are notorious for splitting on the edges, be careful when removing. Those should shine up again after a little scrubbing with a very wet SOS pad.

12-29-2014, 10:37 AM	#3
BLT gmc Registered User Join Date: Feb 2014 Location: West Iowa Posts: 1,106	Re: 1967 gmc hubcap ID... This is the best site I have found for GMC cap ID. http://gmcguy.com/gmc_hubcaps_wheel_..._and_rims.html Bruce

12-29-2014, 03:40 PM	#4
motorcritter Registered User Join Date: Mar 2012 Location: Boulder, CO Posts: 350	Re: 1967 gmc hubcap ID... A good, cheap way to clean up chrome is aluminium foil and soda pop- I'm told that diet Pepsi is best, but they guy that told me drinks that exclusively. Rub the crumpled foil over the surface, using the soda as a wash/lube. Amazing results, especially if it's got specks of corrosion on it. __________________ If 'that which does not kill me, makes me stronger', then I should be Superman by now!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.