What did you get done 1/25/15 edition - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**old Rusty C10** · 01-25-2015, 06:49 PM

We got our first snow this week so I got the beater and the plow working and we used it for the first time she did well STILL trying to get parts for the other two and the more we try to get ahead the harder to get things going but hopefully in the coming week things will fall into place How about you all??

gasmn1620 · 01-25-2015, 08:39 PM

got most of my drop done. The spindles I got were mislabeled so the front is only down 3 inches. Installed energy suspension bushing, inner and outer tie rod ends, pitman arm (very difficult), idler arm, ball joints, upper and lower a-arms, drop springs, flip kit, wheel bearings, brakes, etc. 17 hours and 3 trips to the parts store and it's 90% done.

slotard · 01-25-2015, 10:28 PM

I plastidipped some of the chrome on the front. I'm thinking of doing the trim on the sides too... if I decide I don't like it, it's not too hard to remove.

I'd like to do something about the grill too, not sure what though.

gasmn1620 · 01-25-2015, 10:57 PM

I'm thinking about plasti dipping my whole truck until I'm ready for paint

MalibuSSwagon · 01-25-2015, 10:58 PM

Well starter died so got some help to push the C10 into the garage.

**JIMs70GMC** · 01-25-2015, 11:16 PM

Several things. Had to replace the cap/rotor in my son's 91 Camaro. I had never seen a cap/rotor keep a car from starting, I mean nothing, never tried to fire. Put the cap/rotor on and she fired right up. Has fired up every time now.

Got the clutch/brake pedal assembly in my 86. Going to get the drive shafts shortened this week. Hopefully order the heartthrob exhaust in the next 2 weeks!

Almost been 3 months since I took the k5 off the road to go manual. I am ready to get her on the road.

Jaysonb · 01-26-2015, 12:44 AM

Had some help, so I swapped out my np203, to a np205. Everything works, and I didn't find anything else broken in the process, so it was a good weekend!

bigwheel15 · 01-26-2015, 03:49 AM

Bought a set of window felt/gaskets for both doors at a swap meet and spent a good amount of time fighting to remove the window then fighting the crap fitment of the new stuff. Its better than the pieces that were still there but I now see what all the complaints ive read over things just not fitting when it comes to repop parts for our trucks.

And I still have the driver side to do...yay.

01-25-2015, 06:49 PM	#1
old Rusty C10 Robert Olson Transport Join Date: Oct 2002 Location: recent transplant to NC USA Posts: 20,310	What did you get done 1/25/15 edition We got our first snow this week so I got the beater and the plow working and we used it for the first time she did well STILL trying to get parts for the other two and the more we try to get ahead the harder to get things going but hopefully in the coming week things will fall into place How about you all?? Attached Images __________________ Bob 1951 International running on a squarebody chassis "If a man's worth is judged by the people he associates himself with, then i am the richest man in the world knowing some of the fine people of this board" http://67-72chevytrucks.com/vboard/a...t.php?f=25&a=9 (you can review the site rules here!) PM Me for your vehicle/parts hauling needs in the North East US or see my Facebook page Robert Olson Transport Live each day to the fullest.. you never know when fate is going to pull the rug out from under you... I hate cancer!!

01-25-2015, 08:39 PM	#2
gasmn1620 Registered User Join Date: Oct 2014 Location: panama city, fl Posts: 204	Re: What did you get done 1/25/15 edition got most of my drop done. The spindles I got were mislabeled so the front is only down 3 inches. Installed energy suspension bushing, inner and outer tie rod ends, pitman arm (very difficult), idler arm, ball joints, upper and lower a-arms, drop springs, flip kit, wheel bearings, brakes, etc. 17 hours and 3 trips to the parts store and it's 90% done.

01-25-2015, 10:28 PM	#3
slotard Registered User Join Date: Nov 2014 Location: Alameda, CA Posts: 877	Re: What did you get done 1/25/15 edition I plastidipped some of the chrome on the front. I'm thinking of doing the trim on the sides too... if I decide I don't like it, it's not too hard to remove. I'd like to do something about the grill too, not sure what though. __________________ 1973 C20, 350/350

01-25-2015, 10:57 PM	#4
gasmn1620 Registered User Join Date: Oct 2014 Location: panama city, fl Posts: 204	Re: What did you get done 1/25/15 edition I'm thinking about plasti dipping my whole truck until I'm ready for paint

01-25-2015, 10:58 PM	#5
MalibuSSwagon Registered User Join Date: Sep 2009 Location: Weare,NH Posts: 1,592	Re: What did you get done 1/25/15 edition Well starter died so got some help to push the C10 into the garage. __________________ Eric 1992 Oldsmobile Custom Cruiser 1986 Chevrolet C10\|5.3L\|TKO600\|Shortbed\|Custom Deluxe 1983 Malibu Wagon\|TPI 305\|T5 5 speed\|3.73 non-posi

01-25-2015, 11:16 PM	#6
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	Re: What did you get done 1/25/15 edition Several things. Had to replace the cap/rotor in my son's 91 Camaro. I had never seen a cap/rotor keep a car from starting, I mean nothing, never tried to fire. Put the cap/rotor on and she fired right up. Has fired up every time now. Got the clutch/brake pedal assembly in my 86. Going to get the drive shafts shortened this week. Hopefully order the heartthrob exhaust in the next 2 weeks! Almost been 3 months since I took the k5 off the road to go manual. I am ready to get her on the road. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

01-26-2015, 12:44 AM	#7
Jaysonb Registered User Join Date: May 2009 Location: Good Thunder Mn. Posts: 955	Re: What did you get done 1/25/15 edition Had some help, so I swapped out my np203, to a np205. Everything works, and I didn't find anything else broken in the process, so it was a good weekend!

01-26-2015, 03:49 AM	#8
bigwheel15 Registered User Join Date: Feb 2010 Location: Fort Worth, TX Posts: 727	Re: What did you get done 1/25/15 edition Bought a set of window felt/gaskets for both doors at a swap meet and spent a good amount of time fighting to remove the window then fighting the crap fitment of the new stuff. Its better than the pieces that were still there but I now see what all the complaints ive read over things just not fitting when it comes to repop parts for our trucks. And I still have the driver side to do...yay.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.