![]() |
![]() |
#1 |
Registered User
Join Date: Jun 2002
Location: SPRINGFIELD MO.
Posts: 126
|
70 front spring help
i'm wanting to get the front coils out and cut them, i'v got the shocks unbolted , is there any reason i have to take the drum brakes off?, or can i just pop the lower ball joint lose and lower it to the ground? or should i go with the upper ball joint which is easier? i haven't removed the brakes, it doesn't look like you need to, but you guys are the experts so i'm asking you?
thanks for the help!! andy
__________________
the sun even shines on a dogs a$$ some days!!! |
![]() |
![]() |
![]() |
#2 |
PROJECT 7DEUCE
![]() Join Date: Dec 2002
Location: GRANTS PASS OR
Posts: 21,608
|
When I cut my front spring's I removed the outter tie rod and the upper ball joint and slowly let the assembly down with a floor jack..
__________________
GO BIG GREEN ![]() MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jun 2002
Location: SPRINGFIELD MO.
Posts: 126
|
man this sucks, i can't get either ball joint to let go!
i guess after 34 years thing start to stick a bit!!!!!!!
__________________
the sun even shines on a dogs a$$ some days!!! |
![]() |
![]() |
![]() |
#4 |
PROJECT 7DEUCE
![]() Join Date: Dec 2002
Location: GRANTS PASS OR
Posts: 21,608
|
Are you using a pickle fork??? Should seperatre
__________________
GO BIG GREEN ![]() MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. |
![]() |
![]() |
![]() |
#5 |
Inline 69
Join Date: Apr 2003
Location: valleysprings,california
Posts: 1,018
|
heres frenchblue's original post from january, might help. jeff http://67-72chevytrucks.com/vboard/s...ht=cut+springs
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jun 2002
Location: SPRINGFIELD MO.
Posts: 126
|
yeah i'm using a pickle fork, but it seems like im gunna tear the ball joint boot, i can't get it in there without sandwiching the boot, it just looks like it's going to tear!
__________________
the sun even shines on a dogs a$$ some days!!! |
![]() |
![]() |
![]() |
#7 |
Registered User
![]() Join Date: Apr 2000
Location: Bradenton, FL
Posts: 1,036
|
Instead of busting a ball joint and breaking the boot why dont you unpolt the 2 U-Bolts on the lower controll arm and then get the spring out.
__________________
1970 CST/10 402,700R4,3:73 posi,AC,PS,PB,TLT,PW,Buckets with heaters |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Jun 2002
Location: SPRINGFIELD MO.
Posts: 126
|
thanks for all the help guys!! guess i'll try the u bolt thing and see how it goes.
__________________
the sun even shines on a dogs a$$ some days!!! |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Dec 1999
Location: BRADENTON FLA
Posts: 3,269
|
The way we do it is unbolt the upper a arm at the cross shaft bolts while we have 2 jackstands under the lower cross shafts and a floor jack under the end of the a arm at ball joint, do your cut on the top of the spring, set the bottom in the groove and jack it up lineing the bolts back up and adding the correct shims for alignment.
__________________
Rest in Peace Ed. Thanks for all the good times. |
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Jun 2002
Location: SPRINGFIELD MO.
Posts: 126
|
ruined an upper ball joint but passenger side spring is out, no missing fingers , head is still on, as straight as it ever was, no injuries!
__________________
the sun even shines on a dogs a$$ some days!!! |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Jun 2002
Location: SPRINGFIELD MO.
Posts: 126
|
hey mothertrucker, are you saying to cut the spring at the top? the tapered end?? i would have thaught you cut it at the bottom, one spring round or loop off, sorry i'm not trying to second guess you, just trying to be clear, i'm new at this and just want to be sure.
thanks again everyone! andy
__________________
the sun even shines on a dogs a$$ some days!!! |
![]() |
![]() |
![]() |
#12 |
Watch out for your cornhole !
![]() Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
I always cut the bottom (big end).
__________________
I'm on the Instagram- @Gearhead_Kevin |
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Jun 2002
Location: SPRINGFIELD MO.
Posts: 126
|
am i correct that 1 whole loop or round off of the bottom is approx. 2 inch's?
__________________
the sun even shines on a dogs a$$ some days!!! |
![]() |
![]() |
![]() |
#14 |
Watch out for your cornhole !
![]() Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
For me, it's usually between 2 and 3 inches for 1 coil.
__________________
I'm on the Instagram- @Gearhead_Kevin |
![]() |
![]() |
![]() |
#15 |
Registered User
Join Date: Jun 2002
Location: SPRINGFIELD MO.
Posts: 126
|
cool thanks for the help!!, where the best place to buy upper ball joints and how do you replace them, they look to be riveted on?
__________________
the sun even shines on a dogs a$$ some days!!! |
![]() |
![]() |
![]() |
#16 |
Registered User
Join Date: Dec 1999
Location: BRADENTON FLA
Posts: 3,269
|
Sorry i meant the bottom end. Grind the factory rivets off the ball joint, the new ones come with bolts. MOOG is the best quality.
__________________
Rest in Peace Ed. Thanks for all the good times. |
![]() |
![]() |
![]() |
Bookmarks |
|
|