NE 65 Chevy 1/2 66 Chevy 3/4 Part Out

[paulspickupparts]

Originally Posted by diver

hello,need 1,will take 2 bezel nut for 65 light switch dash .thanks butch and one for wiper 2 speed

Hi Butch . I will look tomorrow to see if I have them.

[diver]

and a wiper switch bezel 1 or 2 thanks radio came today she is a nice one

[Sick5]

Originally Posted by paulspickupparts

Here are some pics of the regulators. The splines are good and the rollers are good . I rolled them up and down several times and they work good. The do have some paint loss and some surface rust but are good used parts. Thanks

ok paypal#???

[paulspickupparts]

Originally Posted by Sick5

ok paypal#???

Paypal is fine . Sent PM with payment information.

[paulspickupparts]

Originally Posted by paulspickupparts

Hi Butch . I will look tomorrow to see if I have them.

Butch , right now I do not have any of the bezels. I have been incuding them when I sell a headlight switch or choke cable. Thanks

[Sick5]

$$ sent

[paulspickupparts]

Originally Posted by paulspickupparts

Remove this dash today. One of the nice ones I have had . Nice radio area. $100 plus shipping.

No response from softballnrd27 . Dash for sale

[Slambone]

How much for the gauge cluster? I can do paypal.

[paulspickupparts]

I took this one out. Speedometer works, good bezel housing, lense has a little loss to some of the lettering, few bulbs missing in the hardware . $60 plus shipping. Thanks

[diver]

hi Paul,had radio put in today put new recone speaker with it and plays like new up and down stations with no antenna in atlanta area.thanks

[paulspickupparts]

Good deal. It was the best one I had at the time. Thanks again.

[sharkskinman]

What about this part
And possibly the metal part that's attached to the frame

[paulspickupparts]

Originally Posted by diver

hi Paul,had radio put in today put new recone speaker with it and plays like new up and down stations with no antenna in atlanta area.thanks

Butch , not sure if you still need it but I have a headlight switch bezel . Shows a little wear. I have a bezel from a choke cable. I will check to see if it is the same as a wiper bezel. Thanks

[paulspickupparts]

Originally Posted by sharkskinman

What about this part
And possibly the metal part that's attached to the frame

I should have but will need to know what the model and year of your truck is. Also how much of the frame you would need . I can cut larger if you need. Thanks

[sharkskinman]

65 swb stepside
Original 230 and Muncie? non syncro 3 on tree
I would think I can drill out the old and weld in the new so I would think all I need is width of connecting metal
But can cut off and weld directly on

Going to look in that area and see if there is anything else broke
(wheel came off n under truck at 25mph and lifted probably 5-6' up and came down hard cracking the drum) now sits low on that corner

[paulspickupparts]

Originally Posted by sharkskinman

65 swb stepside
Original 230 and Muncie? non syncro 3 on tree
I would think I can drill out the old and weld in the new so I would think all I need is width of connecting metal
But can cut off and weld directly on

Going to look in that area and see if there is anything else broke
(wheel came off n under truck at 25mph and lifted probably 5-6' up and came down hard cracking the drum) now sits low on that corner

Ok , let me know what you need . I should be able to get you fixed up.

Thanks

[inkfamous13]

Looking for complete from crossmember wheel to wheel and a coil spring rear end 6 lug c10 and i need choke knob, pass side long bed thick top molding, both pass moldings and bottom cab drivers lil moulding. And need arm rests and drivers vent knob. Ive got a c20 ive gotta get rid of these 8 lugs and super low geared rear. Got a nv-540 od 5 spd trans and still cant top 60 on highway. My number is 4426009184 txt me just say truck parts online

[paulspickupparts]

Originally Posted by inkfamous13

Looking for complete from crossmember wheel to wheel and a coil spring rear end 6 lug c10 and i need choke knob, pass side long bed thick top molding, both pass moldings and bottom cab drivers lil moulding. And need arm rests and drivers vent knob. Ive got a c20 ive gotta get rid of these 8 lugs and super low geared rear. Got a nv-540 od 5 spd trans and still cant top 60 on highway. My number is 4426009184 txt me just say truck parts online

I have the crossmember and coil spring rear end. The biggest problem ends up being shipping. It usually ends up killing the deal. I do not think my bed moldings are good enough. Thanks Paul

[jdl71]

Do you have a wiper switch? Don't need bezel, just the switch. Any more radios?

[paulspickupparts]

Originally Posted by jdl71

Do you have a wiper switch? Don't need bezel, just the switch. Any more radios?

I sold the radio shown. Here is nother one that I took out of a different truck . Looks good but untested. The speaker would have to be reconed. Nice bracket. Original knobs. The wiring has been cut to the speaker . Condition as shown $125 . $15 insured shipping.

Currently sold out of wiper switches.
Thanks

[paulspickupparts]

One more pic.

[jdl71]

Pass for now on the radio. Keep me in mind for a wiper switch if you run across one. Thanks!

[roll_the_dice]

Do you still have the gauge cluster for sale? Price shipped to 31406 please. Thanks

[paulspickupparts]

Originally Posted by jdl71

Pass for now on the radio. Keep me in mind for a wiper switch if you run across one. Thanks!

I looked at more trucks I have . I have a couple of single speed wiper switches but do not have any two speeds right now. Thanks

[paulspickupparts]

Originally Posted by roll_the_dice

Do you still have the gauge cluster for sale? Price shipped to 31406 please. Thanks

The gauge cluster shown has been sold . I have others . Price varies according to condition. I have started breaking them down and selling bezels, speedo odometer gauges seperately as they seem to sell better that way. Clusters run from $60-$100 depending on condition and with or without harness . Thanks