|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
09-25-2016, 09:08 PM
|
#1 |
|
Registered User
Join Date: May 2013
Location: Beavercreek, OH
Posts: 81
|
Frame Hole Measurement Help
I'm in the middle of reworking the frame prior to paint and I need to clean up these two wollared out holes at the end of the frame rails...I believe they are for the bumper brackets. I think the previous owner used a torch to cut the bolts and got a little loosey goosey end enlarged the holes. I plan to just weld them up and redrill but I need the location of hole center.
Can someone take a frame measurement in from the end and from either top or bottom, and measure hole size. Thanks in advance.
__________________
1971 Chevy C-10 Currently is rust repair Last edited by reb162; 09-25-2016 at 09:22 PM. |
|
|
|
09-25-2016, 09:49 PM
|
#2 |
|
Registered User
Join Date: Oct 2008
Location: Marianna Arkansas
Posts: 7,280
|
Re: Frame Hole Measurement Help
Weld from the outside towards inside then grind flat and drill out to a notch bigger than 1/2 so 1/2 inch bolts can go on to bolt up the bumper bracket. Or at least that is what I would do.
|
|
|
|
|
09-26-2016, 07:40 PM
|
#3 |
|
Registered User
Join Date: May 2013
Location: Beavercreek, OH
Posts: 81
|
Re: Frame Hole Measurement Help
That's exactly what I did...I welded up the hole from the outside to the center and ground it smooth on both sides. I welded it completely up though since it was so out of round and couldn't even tell where center was.
So now I need measurements for hole centers so i can redrill. Thanks to anyone that can measure their frame.
__________________
1971 Chevy C-10 Currently is rust repair |
|
|
|
|
09-27-2016, 09:27 PM
|
#4 |
|
Registered User
Join Date: May 2013
Location: Beavercreek, OH
Posts: 81
|
Re: Frame Hole Measurement Help
TTT...hoping someone has a frame they can quickly measure. Was looking to paint my frame this weekend. Thanks again for the assist.
__________________
1971 Chevy C-10 Currently is rust repair |
|
|
|
|
09-27-2016, 11:04 PM
|
#5 |
|
Registered User
Join Date: Jan 2009
Location: San Antonio, Texas
Posts: 1,374
|
Re: Frame Hole Measurement Help
Long bed or short? I never had a factory bumper, but I can go look for the measurements on mine if long bed is OK.
__________________
1972 C10 LWB, 350/350 Deconstruction began 5/2009, mostly completed restoration, 5/2017 |
|
|
|
|
09-27-2016, 11:14 PM
|
#6 |
|
Registered User
Join Date: Jan 2009
Location: San Antonio, Texas
Posts: 1,374
|
Re: Frame Hole Measurement Help
My rear frame rails look a little different than yours. Here is what I have
__________________
1972 C10 LWB, 350/350 Deconstruction began 5/2009, mostly completed restoration, 5/2017 |
|
|
|
|
09-28-2016, 11:37 AM
|
#7 |
|
Registered User
Join Date: May 2013
Location: Beavercreek, OH
Posts: 81
|
Re: Frame Hole Measurement Help
Thanks dfwright! Mine is a short bed frame so maybe that is the difference? Surprised that would make a difference in the rear of the frame.
Anyone with a short bed care to get me measurements? Thanks
__________________
1971 Chevy C-10 Currently is rust repair |
|
|
|
|
09-29-2016, 08:46 PM
|
#8 |
|
Registered User
Join Date: May 2013
Location: Beavercreek, OH
Posts: 81
|
Re: Frame Hole Measurement Help
bump...some short bed frame help here?
__________________
1971 Chevy C-10 Currently is rust repair |
|
|
|
|
10-01-2016, 12:56 PM
|
#9 |
|
Registered User
Join Date: May 2013
Location: Beavercreek, OH
Posts: 81
|
Re: Frame Hole Measurement Help
bump one more time....was looking to paint frame today but need these holes drilled first...
Please, anyone with a short bed frame please provide locating measurements on the two holes in the picture above! Thanks!
__________________
1971 Chevy C-10 Currently is rust repair |
|
|
|
|
10-01-2016, 01:43 PM
|
#10 |
|
Senior Member
 
Join Date: Oct 2014
Location: New Palestine In
Posts: 932
|
Re: Frame Hole Measurement Help
Here's two pics of my SWB 68 frame. Looks like my holes are different than your 71. Bumper bracket is installed so I can't get dimensions.
I say go ahead and paint the frame and drill the holes when you get dimensions. Sorry I couldn't be of more help. Phil
__________________
Phil "Money is only a tool to create and achieve what you want most in life" PayPal: rodnrudy@comcast.net |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
