Clear over polished grille

[rockyrivermark]

Subject been discussed here before using auto clear coats etc with conflicting results.
I'm looking to clear over my polished grille since it always needs polishing. I tried wax over it but doesn't help much
I researched a bit and found a commercial coat especially made for various metals including aluminum.
Used on exterior building and storefront doors etc.
anybody try it? If not I'm game and will post my results.

https://www.everbritecoatings.com/ca...-only-c-7.html

[CG]

Wonder if having it clear powder coated would work?

[Already Gone]

Subscribed

[Ol Blue K20]

Subbed for future info

[beadblaster]

I have used the everbrite on polished rims and various polished parts. Works as described,just make sure you clean the metal with wax and grease remover prior to applying. I have used a spray gun as well as foam brushes to apply and you cannot tell one from the other once dry.

[HeavyD]

How long is the coating expected to last?

[rockyrivermark]

Originally Posted by HeavyD

How long is the coating expected to last?

They also sell it in rattle can.
Not sure how long it lasts. I think a long time being a coating used on high traffic areas such as commercial doors. . Check out the website. I'll try it and post my results
Posted via Mobile Device

[rockyrivermark]

I tried the perma clear today. Tired of constantly polishing the inprotected aluminum, constant battle.
First was to polish with Mothers mag and aluminum polish and microfiber buff by hands . Absolutely amazing stuff by the way.
Then directions for permaclear say to wipe metal with baking soda and water to mutrelize any acid from the polish
Then wipe down with denature alcohol or xylene
Use denatured alcohol! Xylene is nasty stuff. Very high VOC
I bought 4oz bottle and applied with foam brush.
Laid down like a spray finish. Pretty thin stuff.
Anyway. Looks great and I'll post in a month to see how sits holding up.
I think we have something here though
See pics.
Mark.

[Stocker]

Subscribed

[ApacheIvan]

Subscribed!

[70 cst]

Subscribed

[Shinysideup]

I read their info and no mention of UV resistance? They also state easy to strip and redo, how is that accomplished? Did you choose the brush because you applied it already mounted to truck vs the spray?
It looks like the original anodizing with a thin satin finish,is that right?
Thanks for the info.

[rockyrivermark]

Originally Posted by Shinysideup

I read their info and no mention of UV resistance? They also state easy to strip and redo, how is that accomplished? Did you choose the brush because you applied it already mounted to truck vs the spray?
It looks like the original anodizing with a thin satin finish,is that right?
Thanks for the info.

Yes I used the foam brush rather than remove or mask off entire grille
The permaclear gave the finish a bit more gloss finish.
I have to check it this morning now that it's dry.
Not sure on the UV protection. I would email them for more info.
All I know was for $20 on amazon it was worth a shot.

https://www.everbritecoatings.com/ca...ar-ezp-97.html

[custom10nut]

Subscribed

[rockyrivermark]

I checked this morning. The finish looks good. No brush marks although I used a foam brush, either way the stuff laid down nice.
Looks factory and see what time does.
I got the 4oz can and and used very little of it so it goes a long way.
RRM

[ls1nova71]

Sub'd for results in a month.

[CG]

Looks good! I just looked at my dopey earlier comment. Read right past what you were up to and assumed you were looking for ideas ... duh haha.

[Ol Blue K20]

Looks great, I hope it lasts. Waiting for your conclusion on that.

[rockyrivermark]

Originally Posted by Ol Blue K20

Looks great, I hope it lasts. Waiting for your conclusion on that.

I'll keep you posted.
Posted via Mobile Device

[Classic v6 GMC's]

following

[k29349]

I have had Everbrite on some E-T slot mags for 3 years now. They still look great and they get driven a lot.

[67swb72klb]

I think you nailed it looks like an OE finish hope it holds up...

[Tdrcreyn4]

sub

[rockyrivermark]

Originally Posted by Tdrcreyn4

sub

Well I promised I would post one month results.
So far the coating is working great. Looks exactly has it did when I applied it.
Previously for this I was trying wax and other products and having to re polish weekly to get the grill looking nice.
Anyway. Highly recommend
Pic attached.
Posted via Mobile Device

[Keith Seymore]

Relative to my current project at GM: we are using CNC billet polished aluminum for the bright exterior trim (body side moldings, window trim, etc).

We used clear powdercoat over the aluminum (which is the production process for aluminum wheels) but are gravitating towards using automotive clear paint over the aluminum, which gives us a little bit smoother finish.

K