|
04-28-2004, 12:57 AM
|
#1 |
|
Registered User
Join Date: Feb 2004
Location: Victoria B.C.
Posts: 101
|
Body shims
Did the bodys of your jimmys come with body shims to line up the doors so they will close properley?
Thanks for any help |
|
|
|
04-28-2004, 02:16 AM
|
#2 |
|
Registered User
Join Date: Apr 2004
Location: Willits Ca
Posts: 261
|
Yes you can shim the body, but I would check your body mounts, door hinges, the pin is not to hard to replace. Then try to adjust the door and striker. Sometimes the problem is rotten pillar base and cab support, it will cause the Jimmy to sag. It is hard to tell what might be bad under the rocker panels.
|
|
|
|
|
04-28-2004, 02:51 AM
|
#3 |
|
Member since 2000
Join Date: Dec 2000
Location: Mountain View Ca / Mexico
Posts: 7,874
|
i don't think I've seen a door shimmed before, cowl and fender, yes. But like Jimmy said check the body for rust especially the under side.
|
|
|
|
|
04-28-2004, 03:31 PM
|
#4 |
|
go cyclones
Join Date: Jun 2003
Location: Ames, IA
Posts: 1,883
|
shims under the body or the shim-like things that are on the body in the door way.
|
|
|
|
|
04-28-2004, 07:39 PM
|
#5 |
|
Registered User
Join Date: Dec 2003
Location: So Cal
Posts: 179
|
what I did was use a flat washers and cut a slot from the outter edge to the center hole, that way all I needed to do was loosen up the bolt (not remove it) and slide the washer in. Some of the bolts are welded in and if you have carpet you would have to remove things to get them out...so try the "C" washer...
__________________
72 K/5 350/205 SOFT-TOP DOUG THORLEY HEADERS A/C CUSTOM REAR BUMPER http://www.socalbigdawgs.com/tr/7.18.03/DSC04290.JPG |
|
|
|
|
04-28-2004, 10:20 PM
|
#6 |
|
Senior Member
  
Join Date: Jan 2002
Location: Burghill, Ohio 44404
Posts: 3,401
|
You can buy the big flat washers with the cut out allready their but I dont know who sells them I need some for my jimmy Does anyone no where you can get them.
|
|
|
|
|
04-28-2004, 11:06 PM
|
#7 |
|
Member since 2000
Join Date: Dec 2000
Location: Mountain View Ca / Mexico
Posts: 7,874
|
most auto parts store carry shim. Any local automotive paint shop should have them and different sizes in thickness.
|
|
|
|
|
04-29-2004, 12:54 AM
|
#8 |
|
Registered User
Join Date: Feb 2004
Location: Victoria B.C.
Posts: 101
|
Just got in the house from shimming body mounts 2 & 3 to get the doors to close properley. I had changed them all and fastened her all up to find the doors did not close to well. The old mounts were very bad some the bolts were just rattling around in there but the doors did close with out a hitch.
|
|
|
|
|
05-01-2004, 08:22 AM
|
#9 |
|
Senior Member
Join Date: Jun 2001
Location: Shelbyville, KY
Posts: 3,261
|
the GM book talks to shims to the mounts during the initial build process for door alignment so even with perfect inner rocker boxes, you may have to shim with new rubber mounts!!!
|
|
|
|
|
05-07-2004, 11:11 PM
|
#10 |
|
PROJECT 7DEUCE
Join Date: Dec 2002
Location: GRANTS PASS OR
Posts: 21,606
|
I had a similar problem when I put new urethane mount's on my blazer and could not get the door's to shut a little shiming on th ebody mount behind the door's and now they close great..
__________________
GO BIG GREEN  GO DUCKSMEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
