What did you do to your truck today part IV - Page 30 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

karlbenz · 07-31-2018, 10:26 PM

Put the stroker motor in over the weekend, changed front driveshaft, Changed both front brake hoses. broke a bleeder. changed caliper, changed out heater core

69 C10 LWB · 08-04-2018, 03:47 PM

I pulled the 230 and installed a 350. I didn't want to do it but the 230 still wont turn so it has to come apart and I don't want to wait to drive the truck. I also learned the 73 and later manifolds wont fit our trucks, so the almost new exhaust I saved wont do me any good. The driver side manifold dumps down right where the clutch linkage attaches to the frame. It wouldnt have done me much good anyway since I left the pivot ball at home.

karlbenz · 08-05-2018, 04:30 PM

New parklamp and headlight harness from classic parts installed today

RDrancher · 08-05-2018, 08:07 PM

Removed the bulk of someone's idea of custom paint and hard-as-a-rock masking tape from my tailgate.

**Clyde65** · 08-05-2018, 08:29 PM

Got him back from painter, put gas in and put him in the garage until next weekend when I’ll hopefully have time to put him back together!!

I like to say Clyde( truck) is now shacking up with Bonnie( trailer)!!

**nsb29** · 08-06-2018, 07:49 AM

It makes you wonder what goes on when the doors are closed lMAO

vin63 · 08-07-2018, 08:07 PM

Finishing up the last bit of rear suspension work this morning before the forecasted heat.

jchav62 · 08-10-2018, 11:17 AM

Converted to an internally regulated alternator last night. Very simple and everything seems to be running much happier.

69 C10 LWB · 08-11-2018, 02:13 PM

Ive been looking for a set of manifolds for the small block in my truck and stumbled on these. Loosely installed them this morning to check fit. Couldnt do much because the yard at work is wet after the rain and I dont have room inside at the moment

LostMy65 · 08-11-2018, 04:01 PM

Quote:

Originally Posted by 69 C10 LWB

Ive been looking for a set of manifolds for the small block in my truck and stumbled on these. Loosely installed them this morning to check fit. Couldnt do much because the yard at work is wet after the rain and I dont have room inside at the moment

Are those chrome or stainless steel?

**The Rocknrod** · 08-11-2018, 04:21 PM

Quote:

Originally Posted by 69 C10 LWB

Ive been looking for a set of manifolds for the small block in my truck and stumbled on these. Loosely installed them this morning to check fit...

And?

69 C10 LWB · 08-11-2018, 06:08 PM

They are ceramic coated. Unfortunately I didnt have bolts to put them on but they look like there shouldnt be any issues. Clears the clutch linkage no problem but they will be kinda close to the factory starter. They are Jegs p/n 300555, I got them off Craigslist.

forestb · 08-11-2018, 06:24 PM

Got the truck back from interior shop on Tuesday. All and all I am pretty happy.

vin63 · 08-13-2018, 06:35 PM

Got the Poncho back in the PonchoC10...

69 C10 LWB · 08-14-2018, 07:13 PM

Quick update on the Jegs headers. They kid of fit. Im going to have to smash a tube on the driver side or trim some metal from the motor mount. Ill probably trim the mount. The front tube is making contact with the top of the support that attaches to the frame. I also had to grind a little off the flange so that it will clear the factory temp sending unit.

CousinTone · 08-14-2018, 09:42 PM

Quote:

Originally Posted by Clyde65

Got him back from painter, put gas in and put him in the garage until next weekend when I’ll hopefully have time to put him back together!!

I like to say Clyde( truck) is now shacking up with Bonnie( trailer)!!

I’d like to ask Clyde what brand and color his owner put on him? I’ve got similar truck and would love for mine to look like you!!...if you don’t mind

**Clyde65** · 08-15-2018, 07:40 AM

Quote:

Originally Posted by CousinTone

I’d like to ask Clyde what brand and color his owner put on him? I’ve got similar truck and would love for mine to look like you!!...if you don’t mind

It’s the GM Frost White, I’ll get the brand and code for you today.

GreyFox · 08-15-2018, 04:29 PM

Been replacing my bed wood this week. Using my 1955 Radial Arm saw

I'm using 2"x8" and 2"x6" boards. only issue is I have to make all the edges 3/4" to fit properly. It's a bit of a chore to do but I have the tools to make it happen.

**Clyde65** · 08-15-2018, 06:33 PM

Quote:

Originally Posted by CousinTone

I’d like to ask Clyde what brand and color his owner put on him? I’ve got similar truck and would love for mine to look like you!!...if you don’t mind

PPG Frost White

PPG PAINT OMNI AU MBC9700 GM CODE WA8555

karlbenz · 08-16-2018, 06:11 PM

Made me a puke tank outta pvc

Aceslow · 08-16-2018, 06:36 PM

Fixed some cab mounts

Picked up a 12 bolt diff

karlbenz · 08-18-2018, 09:06 PM

got the exhaust on the stroker today. was gonna use ram horns but seemed too close to the valve covers. Ended up getting some flotech headers from oreily's. they fit great

**allchevy58** · 08-19-2018, 07:46 AM

Installed and wired marker lights on the bed.

**62bagger** · 08-19-2018, 07:38 PM

I was able t make some progress this weekend. I brought the air lines up through the floor and routed to the switches and added air gauges. I also got some sound deadener laid down.

Ratman74 · 08-19-2018, 07:43 PM

did some painting on the engine

07-31-2018, 10:26 PM	#726
karlbenz Registered User Join Date: Nov 2008 Location: kannapolis, nc Posts: 528	Re: What did you do to your truck today part IV Put the stroker motor in over the weekend, changed front driveshaft, Changed both front brake hoses. broke a bleeder. changed caliper, changed out heater core __________________ 2000 c3500 utility bed 7.4l 5sp manual old body style. Cab and chassis 1964 GMC K10 383cu in/sm465/twin stick np205 1965 Chevy C60

08-04-2018, 03:47 PM	#727
69 C10 LWB Registered User Join Date: Jan 2012 Location: St Louis Mo Posts: 214	Re: What did you do to your truck today part IV I pulled the 230 and installed a 350. I didn't want to do it but the 230 still wont turn so it has to come apart and I don't want to wait to drive the truck. I also learned the 73 and later manifolds wont fit our trucks, so the almost new exhaust I saved wont do me any good. The driver side manifold dumps down right where the clutch linkage attaches to the frame. It wouldnt have done me much good anyway since I left the pivot ball at home. Attached Images

08-05-2018, 04:30 PM	#728
karlbenz Registered User Join Date: Nov 2008 Location: kannapolis, nc Posts: 528	Re: What did you do to your truck today part IV New parklamp and headlight harness from classic parts installed today __________________ 2000 c3500 utility bed 7.4l 5sp manual old body style. Cab and chassis 1964 GMC K10 383cu in/sm465/twin stick np205 1965 Chevy C60

08-05-2018, 08:07 PM	#729
RDrancher Registered User Join Date: Aug 2014 Location: Decatur, Texas Posts: 673	Re: What did you do to your truck today part IV Removed the bulk of someone's idea of custom paint and hard-as-a-rock masking tape from my tailgate. Attached Images __________________ Romans 10:9 - The Truth

08-05-2018, 08:29 PM	#730
Clyde65 1965 Chevy C10, 2005 4.8L/4l60 Join Date: Aug 2004 Location: DFW Texas Posts: 8,546	Re: What did you do to your truck today part IV Got him back from painter, put gas in and put him in the garage until next weekend when I’ll hopefully have time to put him back together!! I like to say Clyde( truck) is now shacking up with Bonnie( trailer)!! Attached Images __________________ Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684 *support our troops!*

08-06-2018, 07:49 AM	#731
nsb29 Senior Member Join Date: Feb 2014 Location: new smyrna beach fl / 29 palms cal Posts: 1,727	Re: What did you do to your truck today part IV It makes you wonder what goes on when the doors are closed lMAO Last edited by nsb29; 08-06-2018 at 07:56 AM.

08-07-2018, 08:07 PM	#732
vin63 It's Better With Nitro Join Date: Apr 2008 Location: Chino Hills, CA Posts: 2,262	Re: What did you do to your truck today part IV Finishing up the last bit of rear suspension work this morning before the forecasted heat. Attached Images __________________ 1963 C-10: Deluxe-optioned cab, shortbed, fleetside Pontiac 462 ci, Kauffman D-Port alum. heads 4L80E, narrowed sheetmetal Ford 9-inch Tubular front and rear suspension Custom 6-piston front disc and 4-piston rear disc brakes

08-10-2018, 11:17 AM	#733
jchav62 1962 C-10 Join Date: Apr 2005 Location: Las Vegas, New Mexico Posts: 4,978	Re: What did you do to your truck today part IV Converted to an internally regulated alternator last night. Very simple and everything seems to be running much happier. __________________ Joseph Chavez "See the USA in a Chevrolet!!" ......................_____ .........________//__{\_____ ,,,,,,,/__(O)___//___/__(O)_/ 1962 C10 Shortbed Fleetside 327/th350 GV overdrive 1974 C10 Longbed Fleetside 350/th350 "The Trash Truck" 1999 Chevy 2500 OBS, Longbed 5.7/4L80E 4x4 2015 GMC Sierra SLE 1500 4x4

08-11-2018, 02:13 PM	#734
69 C10 LWB Registered User Join Date: Jan 2012 Location: St Louis Mo Posts: 214	Re: What did you do to your truck today part IV Ive been looking for a set of manifolds for the small block in my truck and stumbled on these. Loosely installed them this morning to check fit. Couldnt do much because the yard at work is wet after the rain and I dont have room inside at the moment Attached Images

08-11-2018, 06:08 PM	#737
69 C10 LWB Registered User Join Date: Jan 2012 Location: St Louis Mo Posts: 214	Re: What did you do to your truck today part IV They are ceramic coated. Unfortunately I didnt have bolts to put them on but they look like there shouldnt be any issues. Clears the clutch linkage no problem but they will be kinda close to the factory starter. They are Jegs p/n 300555, I got them off Craigslist. Attached Images

08-11-2018, 06:24 PM	#738
forestb Registered User Join Date: Jan 2009 Location: Burbank, CA Posts: 3,619	Re: What did you do to your truck today part IV Got the truck back from interior shop on Tuesday. All and all I am pretty happy. Attached Images

08-13-2018, 06:35 PM	#739
vin63 It's Better With Nitro Join Date: Apr 2008 Location: Chino Hills, CA Posts: 2,262	Re: What did you do to your truck today part IV Got the Poncho back in the PonchoC10... Attached Images __________________ 1963 C-10: Deluxe-optioned cab, shortbed, fleetside Pontiac 462 ci, Kauffman D-Port alum. heads 4L80E, narrowed sheetmetal Ford 9-inch Tubular front and rear suspension Custom 6-piston front disc and 4-piston rear disc brakes

08-14-2018, 07:13 PM	#740
69 C10 LWB Registered User Join Date: Jan 2012 Location: St Louis Mo Posts: 214	Re: What did you do to your truck today part IV Quick update on the Jegs headers. They kid of fit. Im going to have to smash a tube on the driver side or trim some metal from the motor mount. Ill probably trim the mount. The front tube is making contact with the top of the support that attaches to the frame. I also had to grind a little off the flange so that it will clear the factory temp sending unit. Attached Images

08-15-2018, 04:29 PM	#743
GreyFox Registered User Join Date: Dec 2017 Location: Forest Grove OR Posts: 15	Re: What did you do to your truck today part IV Been replacing my bed wood this week. Using my 1955 Radial Arm saw I'm using 2"x8" and 2"x6" boards. only issue is I have to make all the edges 3/4" to fit properly. It's a bit of a chore to do but I have the tools to make it happen.

08-16-2018, 06:11 PM	#745
karlbenz Registered User Join Date: Nov 2008 Location: kannapolis, nc Posts: 528	Re: What did you do to your truck today part IV Made me a puke tank outta pvc Attached Images __________________ 2000 c3500 utility bed 7.4l 5sp manual old body style. Cab and chassis 1964 GMC K10 383cu in/sm465/twin stick np205 1965 Chevy C60



Register or Log In To remove these advertisements.

08-16-2018, 06:36 PM	#746
Aceslow Registered User Join Date: May 2013 Location: Airdrie Alberta Posts: 27	Re: What did you do to your truck today part IV Fixed some cab mounts Picked up a 12 bolt diff Last edited by Aceslow; 08-16-2018 at 06:52 PM.

08-18-2018, 09:06 PM	#747
karlbenz Registered User Join Date: Nov 2008 Location: kannapolis, nc Posts: 528	Re: What did you do to your truck today part IV got the exhaust on the stroker today. was gonna use ram horns but seemed too close to the valve covers. Ended up getting some flotech headers from oreily's. they fit great __________________ 2000 c3500 utility bed 7.4l 5sp manual old body style. Cab and chassis 1964 GMC K10 383cu in/sm465/twin stick np205 1965 Chevy C60

08-19-2018, 07:46 AM	#748
allchevy58 Senior Member Join Date: Aug 2011 Location: Reno, Nv. Posts: 1,440	Re: What did you do to your truck today part IV Installed and wired marker lights on the bed. Attached Images __________________ 1927 Willy's Knight 24,000 original miles, 1958 Impala 283/Powerglide, 1971 Monte Carlo 350/350, 1972 GMC K2500 350/350, 1976 Chev. K10 350/350, 2006 GMC Sierra 2500HD LBZ Duramax/Allison, 2006 Chev. Silverado K3500 LBZ Duramax/Allison

08-19-2018, 07:38 PM	#749
62bagger Senior Member Join Date: Mar 2016 Location: Sonora California Posts: 285	Re: What did you do to your truck today part IV I was able t make some progress this weekend. I brought the air lines up through the floor and routed to the switches and added air gauges. I also got some sound deadener laid down. Attached Images

08-19-2018, 07:43 PM	#750
Ratman74 Registered User Join Date: Jul 2017 Location: Bunker Hill, WV Posts: 127	Re: What did you do to your truck today part IV did some painting on the engine Attached Images __________________ Dan "Ratman" Ratcliffe Fourth generation Chevy truck guy, raising the fifth 1978 Scottsdale Big 10 "Bad Medicine" Daily Driver 28 yrs 1965 C10 Panel Truck "RWC" http://www.67-72chevytrucks.com/vboa...d.php?t=749003

Register or Log In To remove these advertisements.