MD Parting 72 burb

[richard2717]

Originally Posted by roastmaster

Glove box door?
Az 85205

in good shape with minor scratches. It also has the slightest dent about 4" over from the left and centered height wise.

It will fit in large flat rate so $40 shipped. PP in my signature below if you want it.

.

SOLD

[THECRAZYKIDJR]

Do you have any of the following?

Inside fuel neck cover for burb

Tail & rev light spot welded inserts

High floor hump

Thanks for checking

[richard2717]

Jim
I should have the spot welded inserts.
I have one cover left but it needs a little work
I will have to check to see if I still have an extra high hump.
Let me check on all that and will get back with you in the morning

Thanks
Richard

[richard2717]

Originally Posted by THECRAZYKIDJR

Do you have any of the following?

Inside fuel neck cover for burb

Tail & rev light spot welded inserts

High floor hump

Thanks for checking

Jim,
A question and a couple pics

The high hump do you need one without holes or with, if with any particular setup? I might have a no hole one as well as a 2wd 4spd one



.

[richard2717]

The inner gas cover is in decent shape other than the mounting flange. I started repair on it but this is how it sits now will still need finished


.

[THECRAZYKIDJR]

Richard,

I need a hump for 4sp 4wd...but I can cut the shifter holes if you have a better one without holes

I would like the fuel tank cover and the best set of tail & rev light tins that you have.

I have a fed ex account for the shipping.

Thanks for taking the time.

Jim

[ItsMe253]

Do You have a 67 Suburban door panel, window regulator, tracks/channels, and glass for the rear stationary drivers side area?

[richard2717]

Originally Posted by THECRAZYKIDJR

Richard,

I need a hump for 4sp 4wd...but I can cut the shifter holes if you have a better one without holes

I would like the fuel tank cover and the best set of tail & rev light tins that you have.

I have a fed ex account for the shipping.

Thanks for taking the time.

Jim

Jim
Have not forgot you. Been raining here so not been able to get tail light buckets cut out to check for hidden damage. I cant seem to find my no hole hump so the one I pictured I guess is it. I will try to get the other stuff together tomorrow if the rain quits so i can get you a total

thanks
Richard

[richard2717]

Originally Posted by ItsMe253

Do You have a 67 Suburban door panel, window regulator, tracks/channels, and glass for the rear stationary drivers side area?

I do have a nice 4th door metal panel. do you need the top retainer bar for it?







regulator I know I do not have. The couple I may have are 72 only

I need to check to see if I have the track stuff once the rain lets up here.

Do you need soft ray or clear glass? I think i have both


Thanks
Richard



.

[THECRAZYKIDJR]

Richard,

Thanks for the update.
The weather you had today, is the weather coming to me tomorrow...however, we start as freezing rain...that'll be awesome!

Thanks again
Jim

[ItsMe253]

Door panel looks good what is that piece around the knob hole, is that something they did on these instead of plastic washers? It comes off? My others panels dont have those. Clear glass would work both pieces and any other parts for that 4th door area as mine is empty

[Madkidd007]

Originally Posted by ItsMe253

Door panel looks good what is that piece around the knob hole, is that something they did on these instead of plastic washers? It comes off? My others panels dont have those. Clear glass would work both pieces and any other parts for that 4th door area as mine is empty

Here’s a little reference for ya

[Chevys4life]

Richard do you have another one of the gas tank filler neck assemblies that you have in the pictures for sale that was used on the blazers?

[richard2717]

Originally Posted by THECRAZYKIDJR

Richard,

Thanks for the update.
The weather you had today, is the weather coming to me tomorrow...however, we start as freezing rain...that'll be awesome!

Thanks again
Jim

Jim
Got the buckets cut off this morning and popped them in the blast cabinet to hit the worst spots. Wanted to make sure nothing was hidden. They are all in good shape other than one has a couple pin holes as shown in the pic. The 1st high hump is the only one I can seem to lay my hands on but I would assume the 4x4 hole would be the same position between auto and 4spd (but can't say for sure). Let me know what if any you still have interest in and PM your address so I can get you an accurate shipping quote.

Thanks
Richard

[richard2717]

Originally Posted by ItsMe253

Door panel looks good what is that piece around the knob hole, is that something they did on these instead of plastic washers? It comes off? My others panels dont have those. Clear glass would work both pieces and any other parts for that 4th door area as mine is empty

As stated above the plastic grommet is original. Yours may have crumbled and fell off at some point. They are available aftermarket.

I have a clear 4th door 1/4 glass with good gasket Both window tracks with hardware (1st pic looks tinted but it is not. That was mildew I wiped off for 2nd pic)

A usable widow regulator (will need cleanup, possible new plastic rollers and greasing)

The only 4th door window glass I have is Soft ray factory tint.

Let me know what you are interested in, pm your address so I can get accurate shipping quote

Thanks
Richard

.

[richard2717]

Originally Posted by Chevys4life

Richard do you have another one of the gas tank filler neck assemblies that you have in the pictures for sale that was used on the blazers?

This is the only Blazer neck I have at the moment. The vent tube was cut short for some reason but it is in great shape otherwise $40 shipped


.

[THECRAZYKIDJR]

Richard,

That all looks good.
I'll PM my address and I have a fed ex account, all you have to do is box it, address it and drop at a fed ex store.
Just need price so I can pay you.

Thanks
Jim

[Chevys4life]

Thanks for the picture Richard. I was looking for something similar to the one in the picture. I need something to hook up to my gas tank relocation in my C20.

[richard2717]

Originally Posted by Chevys4life

Thanks for the picture Richard. I was looking for something similar to the one in the picture. I need something to hook up to my gas tank relocation in my C20.

Way too many pics in this post. Let me know which post number you are referencing and I will check what i have.

[Chevys4life]

Picture attachment #1767063 which shows the red arrow pointing to it.

[richard2717]

oh ok I forgot that one was posted. It is not available at this time

[Chevys4life]

Thanks for checking. No problem Richard

[richard2717]

Originally Posted by ShortbedClayton

Do you have the aux. fuel neck and cover plate from the orange and white truck you parted? The neck that is in the bedside?
Posted via Mobile Device

I was able to get everything removed between yesterday and today. I will post pics now but still gotta figure up costs. I also took pictures of the routing of the wire harness. Pretty simple but pics always help. The only cut in the harness is the blue wire right where it hooks to tank. Basically just needs a connector on the end. the inner gas cover is missing one screw all others in good shape. Gas neck screws in good shape. I was able to remove the locking cap without damage to the neck.

Richard

[richard2717]

more pics for Clayton

.

[richard2717]

and one more

.