CO Auto tilt column - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**clay68c10** · 03-31-2019, 04:28 PM

$250 shipped in lower 48

Please respond in thread only per board rules, first "I'll take it" gets it. PayPal is fine, or whatever works for you.

Selling a motor home tilt column, but it has most of the truck features. This was removed from an early 70's motor home, it was a weird chassis I've never seen before.

The NSS hole is in the truck position, never had a switch installed. It had the remains of tape over the opening and the fastener holes are un-threaded.

The lower shift arm is also the truck type.

It has the truck-style rubber oval shaped boot. It was just hanging out under the dash. The 2-bolt flange wasn't there.

The hazard button is the old style, as is the shift indicator font.

Tilt mechanism is tight and smooth. It has a slight tightness at the upper-most adjustment. This is due to one of the lock pawls having a slightly tall tooth. It doesn't affect the workings of it, but I wanted to disclose it.

The 4 bolts in the tilt mechanism that typically loosen over time have been removed and reinstalled with lock-tight.

Tilt pivots were cleaned and lubed when removed to tighten the bolts.

The bottom bearing was greased and is in good shape.

The shift indicator bulb was replaced and tested OK, it has the amber shade on it.

Shifter lever end (inside column) is good, pivot is average

Turn signal, tilt lever, and shifter lever are nice

Turn signal switch is tight and cancels as it should

Turn signal has the curved connector

The illumination wire is long enough to be spliced well under the dash

No Neutral Safety/Reverse switch

This column is good for a driver. It's clean but has some scratches and some thin paint toward the top of the tube, as well as some runs on the indicator housing. Must have been a Friday build.

It would be a great candidate for a scuff and shoot if you wanted to make it really nice.

I'm including a shift indicator from Speedway Motors, they had a $5 sale on them and I picked up a couple. It fits, not sure how it lines up with the actual gear selected.

**clay68c10** · 03-31-2019, 04:31 PM

Pictures

**clay68c10** · 03-31-2019, 04:32 PM

More pictures

*randy500* · 03-31-2019, 05:15 PM

Can you do $225 shipped on this?

thehata1 · 03-31-2019, 09:15 PM

How much for a local pickup?

*randy500* · 03-31-2019, 10:10 PM

I will take it at your asking price of $250 shipped.

**clay68c10** · 03-31-2019, 11:06 PM

Sold to Randy.
I’ll shoot you a PM

*randy500* · 04-01-2019, 01:13 AM

Quote:

Originally Posted by clay68c10

Sold to Randy.
I’ll shoot you a PM

Money sent, my address in PayPal is corret, thank you!

03-31-2019, 04:28 PM	#1
clay68c10 Senior Member Join Date: Aug 2004 Location: Centennial, CO Posts: 2,991	Auto tilt column $250 shipped in lower 48 Please respond in thread only per board rules, first "I'll take it" gets it. PayPal is fine, or whatever works for you. Selling a motor home tilt column, but it has most of the truck features. This was removed from an early 70's motor home, it was a weird chassis I've never seen before. The NSS hole is in the truck position, never had a switch installed. It had the remains of tape over the opening and the fastener holes are un-threaded. The lower shift arm is also the truck type. It has the truck-style rubber oval shaped boot. It was just hanging out under the dash. The 2-bolt flange wasn't there. The hazard button is the old style, as is the shift indicator font. Tilt mechanism is tight and smooth. It has a slight tightness at the upper-most adjustment. This is due to one of the lock pawls having a slightly tall tooth. It doesn't affect the workings of it, but I wanted to disclose it. The 4 bolts in the tilt mechanism that typically loosen over time have been removed and reinstalled with lock-tight. Tilt pivots were cleaned and lubed when removed to tighten the bolts. The bottom bearing was greased and is in good shape. The shift indicator bulb was replaced and tested OK, it has the amber shade on it. Shifter lever end (inside column) is good, pivot is average Turn signal, tilt lever, and shifter lever are nice Turn signal switch is tight and cancels as it should Turn signal has the curved connector The illumination wire is long enough to be spliced well under the dash No Neutral Safety/Reverse switch This column is good for a driver. It's clean but has some scratches and some thin paint toward the top of the tube, as well as some runs on the indicator housing. Must have been a Friday build. It would be a great candidate for a scuff and shoot if you wanted to make it really nice. I'm including a shift indicator from Speedway Motors, they had a $5 sale on them and I picked up a couple. It fits, not sure how it lines up with the actual gear selected. __________________ ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO http://67-72chevytrucks.com/vboard/s...d.php?t=788602 93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday... 05 Jeep Wrangler Unlimited. 3” lift & 6-speed 02 E320 the insurance total “free car” 13 Tahoe LTZ Last edited by clay68c10; 03-31-2019 at 04:40 PM.

03-31-2019, 04:31 PM	#2
clay68c10 Senior Member Join Date: Aug 2004 Location: Centennial, CO Posts: 2,991	Re: Auto tilt column Pictures Attached Images __________________ ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO http://67-72chevytrucks.com/vboard/s...d.php?t=788602 93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday... 05 Jeep Wrangler Unlimited. 3” lift & 6-speed 02 E320 the insurance total “free car” 13 Tahoe LTZ

03-31-2019, 04:32 PM	#3
clay68c10 Senior Member Join Date: Aug 2004 Location: Centennial, CO Posts: 2,991	Re: Auto tilt column More pictures Attached Images __________________ ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO http://67-72chevytrucks.com/vboard/s...d.php?t=788602 93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday... 05 Jeep Wrangler Unlimited. 3” lift & 6-speed 02 E320 the insurance total “free car” 13 Tahoe LTZ

03-31-2019, 05:15 PM	#4
randy500 Account Suspended Join Date: Jul 2016 Location: Tacoma, WA Posts: 6,873	Re: Auto tilt column Can you do $225 shipped on this?

03-31-2019, 09:15 PM	#5
thehata1 Registered User Join Date: Dec 2017 Location: Mile High Posts: 160	Re: Auto tilt column How much for a local pickup?

03-31-2019, 10:10 PM	#6
randy500 Account Suspended Join Date: Jul 2016 Location: Tacoma, WA Posts: 6,873	Re: Auto tilt column I will take it at your asking price of $250 shipped.

03-31-2019, 11:06 PM	#7
clay68c10 Senior Member Join Date: Aug 2004 Location: Centennial, CO Posts: 2,991	Re: Auto tilt column Sold to Randy. I’ll shoot you a PM __________________ ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO http://67-72chevytrucks.com/vboard/s...d.php?t=788602 93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday... 05 Jeep Wrangler Unlimited. 3” lift & 6-speed 02 E320 the insurance total “free car” 13 Tahoe LTZ



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.