47-55.1 Window regulator rebuild?? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**8man** · 05-25-2019, 06:19 PM

Well, the PO messed up the riders side window regulator and even drilled a hole in it.

IMG_0081 by Robert Moorman, on Flickr

So I need to rebuild it. I have a spare drivers side, but no riders side. I can get it apart to replace the shaft, even got the spring off, safely I might add.

IMG_0082 by Robert Moorman, on Flickr

The Question:

Does anyone have a trick to get the spring back on?

Thanks.

MiraclePieCo · 05-25-2019, 08:25 PM

Quote:

Originally Posted by 8man

Does anyone have a trick to get the spring back on?

I put new springs in mine, as I recall it was easy if you crank the regulator all the way to the down side (I think - or maybe it was the up side...oh well, you'll figure it out). That way there's virtually no tension on it. But jeez, as chewed up at that spline is, I'd consider replacing the regulator.

Sorry if I'm posting too much today guys - it's pouring rain outside and I have nothing else to do!

**Dan in Pasadena** · 05-25-2019, 09:23 PM

Those splines aren't worth trying to rebuild.

**8man** · 05-25-2019, 09:36 PM

Dan, I was going to replace the worn shaft with the shaft in the second picture if I can get the spring back on.

MARTINSR · 05-26-2019, 01:34 AM

I have a pair of NORS rebuild kits that I bought off eBay years ago for mine. They have that shaft in them.

Brian

**8man** · 05-26-2019, 01:02 PM

Ok, got it changed out and it works fine. Looks funny until I can get the right rivets. Can't put the spring back with those long bolts.

IMG_0084 by Robert Moorman, on Flickr

Now where to find rivets that finish out at 1/4" long and are 0.1455 in diameter...

MiraclePieCo · 05-26-2019, 05:16 PM

Quote:

Originally Posted by 8man

Now where to find rivets that finish out at 1/4" long and are 0.1455 in diameter...

Instead of rivets I've seen guys just use short machine screws with thin nyloc nuts.

**8man** · 05-26-2019, 05:19 PM

Pie, after looking for rivets on line, I think I'll try it your way. It looks like it would work as described. Thanks.

Matt_50 · 05-26-2019, 08:09 PM

I did one with rivets, new inner shaft bent!

Are you replacing the rollers too? I redid one regulator and bought a new one, but I can't get them to roll up quite right so keep us posted.

**8man** · 05-26-2019, 08:43 PM

Not replacing the rollers, just the one shaft. It seems to work fine.

What rivets did you use and where did you get them?

Matt_50 · 05-26-2019, 11:40 PM

They came with the replacement piece. Had to carefully hold it all in a vise and use a punch to beat the rivets.

MARTINSR · 05-26-2019, 11:43 PM

I don't see the big deal, just put bolts. The only reason they used the rivets was for speed and they had no plan on them being rebuilt (they do commonly last 70 years! LOL) but bolts will work just fine.

Brian

**8man** · 05-27-2019, 08:18 AM

Thanks Brian, I'll stick to the bolts.

I did the factory style rivets on a vent window and they are a real pain without the factory setup.

**mr48chev** · 05-27-2019, 02:40 PM

The Filling station has (shows) the pieces to replace that shaft. Plus they have the correct rivets but they are driven rivets. They also have the rollers.

https://www.parts123.com/parts123/yb...rt~A2~cadefefx

**8man** · 06-01-2019, 08:30 AM

Got some #8 machine screws with washers and lock washers to finish my repair.

IMG_0087 by Robert Moorman, on Flickr

IMG_0088 by Robert Moorman, on Flickr

And now it works like it's supposed to. Everything fit back nicely.

MARTINSR · 06-01-2019, 11:31 AM

Right on!

Brian

Matt_50 · 06-01-2019, 02:03 PM

Let us know how window looks once in. I'm still not sure what I did wrong.

05-25-2019, 06:19 PM	#1
8man Senior Member Join Date: Sep 2017 Location: Bryan, Texas Posts: 2,379	Window regulator rebuild?? Well, the PO messed up the riders side window regulator and even drilled a hole in it. IMG_0081 by Robert Moorman, on Flickr So I need to rebuild it. I have a spare drivers side, but no riders side. I can get it apart to replace the shaft, even got the spring off, safely I might add. IMG_0082 by Robert Moorman, on Flickr The Question: Does anyone have a trick to get the spring back on? Thanks. __________________ 8man-aka Robert 1948 on a S10 Frame, small block with a carb 1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL] [/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204

05-25-2019, 09:23 PM	#3
Dan in Pasadena Senior Member Join Date: Nov 2008 Location: Glendora, CA Posts: 6,341	Re: Window regulator rebuild?? Those splines aren't worth trying to rebuild. __________________ '55 Big Window Shortbed, Drive-It-&-Work-On-It slid down the "slippery slope" to a Frame-Off Rodstoration! LQ4/4l85e/C4 IFS/Mustang 8.8 rearend w/3.73's Dan's '55 Big Window "Build" - Well, Kinda!

05-25-2019, 09:36 PM	#4
8man Senior Member Join Date: Sep 2017 Location: Bryan, Texas Posts: 2,379	Re: Window regulator rebuild?? Dan, I was going to replace the worn shaft with the shaft in the second picture if I can get the spring back on. __________________ 8man-aka Robert 1948 on a S10 Frame, small block with a carb 1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL] [/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204

05-26-2019, 01:34 AM	#5
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: Window regulator rebuild?? I have a pair of NORS rebuild kits that I bought off eBay years ago for mine. They have that shaft in them. Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

05-26-2019, 01:02 PM	#6
8man Senior Member Join Date: Sep 2017 Location: Bryan, Texas Posts: 2,379	Re: Window regulator rebuild?? Ok, got it changed out and it works fine. Looks funny until I can get the right rivets. Can't put the spring back with those long bolts. IMG_0084 by Robert Moorman, on Flickr Now where to find rivets that finish out at 1/4" long and are 0.1455 in diameter... __________________ 8man-aka Robert 1948 on a S10 Frame, small block with a carb 1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL] [/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204

05-26-2019, 05:19 PM	#8
8man Senior Member Join Date: Sep 2017 Location: Bryan, Texas Posts: 2,379	Re: Window regulator rebuild?? Pie, after looking for rivets on line, I think I'll try it your way. It looks like it would work as described. Thanks. __________________ 8man-aka Robert 1948 on a S10 Frame, small block with a carb 1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL] [/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204

05-26-2019, 08:09 PM	#9
Matt_50 Registered User Join Date: Jul 2017 Location: Joshua, Texas. Posts: 1,303	Re: Window regulator rebuild?? I did one with rivets, new inner shaft bent! Are you replacing the rollers too? I redid one regulator and bought a new one, but I can't get them to roll up quite right so keep us posted. __________________ 1950 Build

05-26-2019, 08:43 PM	#10
8man Senior Member Join Date: Sep 2017 Location: Bryan, Texas Posts: 2,379	Re: Window regulator rebuild?? Not replacing the rollers, just the one shaft. It seems to work fine. What rivets did you use and where did you get them? __________________ 8man-aka Robert 1948 on a S10 Frame, small block with a carb 1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL] [/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204

05-26-2019, 11:40 PM	#11
Matt_50 Registered User Join Date: Jul 2017 Location: Joshua, Texas. Posts: 1,303	Re: Window regulator rebuild?? They came with the replacement piece. Had to carefully hold it all in a vise and use a punch to beat the rivets. __________________ 1950 Build

05-26-2019, 11:43 PM	#12
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: Window regulator rebuild?? I don't see the big deal, just put bolts. The only reason they used the rivets was for speed and they had no plan on them being rebuilt (they do commonly last 70 years! LOL) but bolts will work just fine. Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

05-27-2019, 08:18 AM	#13
8man Senior Member Join Date: Sep 2017 Location: Bryan, Texas Posts: 2,379	Re: Window regulator rebuild?? Thanks Brian, I'll stick to the bolts. I did the factory style rivets on a vent window and they are a real pain without the factory setup. __________________ 8man-aka Robert 1948 on a S10 Frame, small block with a carb 1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL] [/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204

05-27-2019, 02:40 PM	#14
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,706	Re: Window regulator rebuild?? The Filling station has (shows) the pieces to replace that shaft. Plus they have the correct rivets but they are driven rivets. They also have the rollers. https://www.parts123.com/parts123/yb...rt~A2~cadefefx __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

06-01-2019, 08:30 AM	#15
8man Senior Member Join Date: Sep 2017 Location: Bryan, Texas Posts: 2,379	Re: Window regulator rebuild?? Got some #8 machine screws with washers and lock washers to finish my repair. IMG_0087 by Robert Moorman, on Flickr IMG_0088 by Robert Moorman, on Flickr And now it works like it's supposed to. Everything fit back nicely. __________________ 8man-aka Robert 1948 on a S10 Frame, small block with a carb 1954 Cab, 53 Front and Bed, 50 Doors, S10 Frame, Power TBD Build thread: "]http://67-72chevytrucks.com/vboard/showthread.php?t=746899&highlight=wife%27s+48[/URL] [/URL]http://67-72chevytrucks.com/vboard/showthread.php?t=840204

06-01-2019, 11:31 AM	#16
MARTINSR Registered User Join Date: Dec 2000 Location: Boise, Idaho Posts: 6,003	Re: Window regulator rebuild?? Right on! Brian __________________ 1948 Chevy pickup Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats! Bought with paper route money in 1973 when I was 15. "Fan of most anything that moves human beings"

06-01-2019, 02:03 PM	#17
Matt_50 Registered User Join Date: Jul 2017 Location: Joshua, Texas. Posts: 1,303	Re: Window regulator rebuild?? Let us know how window looks once in. I'm still not sure what I did wrong. __________________ 1950 Build



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.