The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-21-2020, 11:03 PM   #1
HeavyHauler
Registered User
 
Join Date: Nov 2011
Location: USA
Posts: 410
Cant get track bar bolt out of the bracket on my 1968 Chevy C10

I am trying to remove the factory rear differential track bar on my 1968 Chevy C10 short bed fleetside and the bolt that goes through the bracket on the frame side will not come out.

I was able to remove the end connected on the 12 bolt differential but the frame side bolt will not come out at all.

What is the trick in getting that bolt out of the bracket so I can get the track bar out of the bracket?

The track bar is factory and looks like it has never been removed before most likely.
HeavyHauler is online now   Reply With Quote
Old 03-21-2020, 11:25 PM   #2
69Tom
Registered User
 
69Tom's Avatar
 
Join Date: Jul 2015
Location: Phoenix, AZ
Posts: 1,335
Re: Cant get track bar bolt out of the bracket on my 1968 Chevy C10

It's probably just stuck in there. Put the nut back on part way and give it a couple of good whacks with a hammer. I removed mine about 2 or 3 months ago, but can't remember if I had any issues or not with it.
69Tom is offline   Reply With Quote
Old 03-21-2020, 11:40 PM   #3
saxart
Registered User
 
saxart's Avatar
 
Join Date: Aug 2012
Location: St. Croix River Valley, WI
Posts: 795
Re: Cant get track bar bolt out of the bracket on my 1968 Chevy C10

Did you try to drive the bolt out with a punch and hammer?
__________________
Meet "Old Roy": http://67-72chevytrucks.com/vboard/s...d.php?t=707801
saxart is offline   Reply With Quote
Old 03-21-2020, 11:54 PM   #4
ltdmstr
Registered User
 
ltdmstr's Avatar
 
Join Date: Jul 2016
Location: Deerfield IL
Posts: 108
Re: Cant get track bar bolt out of the bracket on my 1968 Chevy C10

I did mine a couple weeks ago and it was a huge PIA. There's a steel sleeve inside the rubber bushing and that was rusted solid to the bolt and the dried rubber was on it just as well. The nut snapped off when I tried to remove it. Then after spending several hours fighting to get the remainder out, I ended up drilling the bolt head and snapping it off. Even after both the bolt head and nut were off it probably took another half an hour to get it apart. If I had to do over again, I'd try using a sawzall to cut the bolt inside the frame bracket. Oh, and if it's anything like mine, after you get the bar out of the frame, you'll need a hydraulic press to get the rubber and bushing out. At least that part was quick and easy.
ltdmstr is offline   Reply With Quote
Old 03-22-2020, 12:04 AM   #5
custom10nut
Registered User
 
custom10nut's Avatar
 
Join Date: Apr 2015
Location: East Tn (In the heart of the Smoky Mtns)
Posts: 1,887
Re: Cant get track bar bolt out of the bracket on my 1968 Chevy C10

Heat it up and hit it a few times with a BFH.
You could also tried soaking it with penetrating oil, and tapping on it to create the vibration to let the oil do its job. Repeat this every day for three or four days, and it should come loose
custom10nut is online now   Reply With Quote
Old 03-22-2020, 11:02 AM   #6
kidatheart
Senior Member
 
kidatheart's Avatar
 
Join Date: May 2012
Location: Assaria, Ks
Posts: 465
Re: Cant get track bar bolt out of the bracket on my 1968 Chevy C10

A little careful persuasion with "gas axe" can help....
kidatheart is offline   Reply With Quote
Old 03-22-2020, 01:16 PM   #7
HeavyHauler
Registered User
 
Join Date: Nov 2011
Location: USA
Posts: 410
Re: Cant get track bar bolt out of the bracket on my 1968 Chevy C10

My track bar is stuck just like Itdmstr was saying. I hit mine with a 2lb hammer like crazy and then I hit it with a 5lb hammer and it would not budge. I then got out a air hammer and it also did nothing.

I will try to cut it out tomorrow. I will most likely destroy the factory track bar but at least it will be out and can put the new one in. LOL!
HeavyHauler is online now   Reply With Quote
Old 03-22-2020, 05:58 PM   #8
68 P.O.S.
Registered User
 
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,662
Re: Cant get track bar bolt out of the bracket on my 1968 Chevy C10

I did mine 2 months ago and had the same experience with the sleeve rust welded to the bolt. I sawzall'd both sides. It was a pita for sure.
__________________
72 C10 lwb fleetside -stock 350/350 combo
68 P.O.S. is offline   Reply With Quote
Old 03-23-2020, 03:12 PM   #9
maverickmk
Senior Member
 
maverickmk's Avatar
 
Join Date: Nov 2019
Location: Cocoa FL
Posts: 596
Re: Cant get track bar bolt out of the bracket on my 1968 Chevy C10

Quote:
Originally Posted by custom10nut View Post
Heat it up and hit it a few times with a BFH.
You could also tried soaking it with penetrating oil, and tapping on it to create the vibration to let the oil do its job. Repeat this every day for three or four days, and it should come loose
Don't do both of these at the same time
__________________
Die with memories, not dreams.

Not to brag, but I don't need alcohol to make really bad decisions.

1969 GMC Short Step Side
maverickmk is offline   Reply With Quote
Old 04-16-2020, 03:04 PM   #10
HeavyHauler
Registered User
 
Join Date: Nov 2011
Location: USA
Posts: 410
Re: Cant get track bar bolt out of the bracket on my 1968 Chevy C10

Quote:
Originally Posted by maverickmk View Post
Don't do both of these at the same time
I ended up having to cut the bolt and I was able to save the factory track bar with zero damage to the bracket.
HeavyHauler is online now   Reply With Quote
Old 04-16-2020, 03:56 PM   #11
HO455
Post Whore
 
HO455's Avatar
 
Join Date: Feb 2016
Location: Portland Oregon
Posts: 11,351
Re: Cant get track bar bolt out of the bracket on my 1968 Chevy C10

Congratulations on the great work and saving both pieces.
__________________
Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help.
RIP Bob Parks.
1967 Burban (the WMB),1988 S10 Blazer (the Stink10 II),1969 GTO (the Goat), 1970 Javelin, 1952 F2 Ford OHC six 4X4, 29 Model A, 72 Firebird (the DBP Bird). 85 Alfa Romeo
If it breaks I didn't want it in the first place
The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377
HO455 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:59 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com