A freebie! 1986 C10 Longbed - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Nick_R_23 · 08-31-2020, 09:25 AM

Something interesting!

It’s a KEM engine rated at 304HP/396TQ.

LT7A · 08-31-2020, 03:26 PM

Quote:

Originally Posted by Nick_R_23

Something interesting!

It’s a KEM engine rated at 304HP/396TQ.

I would like to know about this. Those are very good truck numbers.

Nick_R_23 · 08-31-2020, 04:10 PM

http://www.kemequipment.com/manuals/...r-curve-57.pdf

Nick_R_23 · 09-04-2020, 02:14 PM

Prepping the spindles for installation later today!

Nick_R_23 · 09-05-2020, 02:02 AM

Front end disassembled and being prepped for the new spindles!

Cut 1 complete coil out of the spring, about 2” additional drop over the 2.5” spindles.

Spring and spindle reinstalled.

My dumb ass forgot to check the brake package before ordering the spindles...turns out this truck actually had the 1” rotors! So, perfect time to convert to JB5 rotors and calipers!

Caliper and new pads installed! I’ll have to wait until tomorrow on the hoses, they ended up being a day out.

Since the front end isn’t complete yet, enjoy another glorious rear end shot!

jjzepplin · 09-05-2020, 09:14 AM

Fancy indeed! Nothing wrong with a good rear shot.

Nick_R_23 · 09-06-2020, 02:38 AM

Thanks!

I finished up the driver side today with a new brake line!

Completed the passenger side too!

Installed the sway bar lowering brackets!

Sway bar reinstalled!

The front end is all back together!

Back on all fours!

This is perfection! Exactly what I was going for!

jjzepplin · 09-06-2020, 09:24 AM

That is very nice! Do you have any information on the kit you used?

Nick_R_23 · 09-06-2020, 10:58 AM

Thank you! And yes, I do! Overall, this is about a 4.5” front/6” rear drop. Current tire size is 235/70R15, I will likely keep that front size and go 275/60R15 in the rear.

The drop spindles are Classic Performance CLP-CP4s4 2.5” drop spindles. https://www.summitracing.com/parts/clp-cp4s4

The coil springs are stock 1/2 ton V8 springs with 1 complete coil cut as seen in the pictures, equal to about 2” additional drop. The rear leaf springs are the stock 3+1 spring pack, the overload spring is intact and no leafs were removed.

The axle flip kit is UMI Performance UPI-6410, with a 6” drop. https://www.summitracing.com/parts/upi-6410

The shock extensions are UMI Performance UPI-6411. https://www.summitracing.com/parts/upi-6411

The sway bar relocation kit is Classic Performance CLP- 6372LSB. https://www.summitracing.com/parts/clp-6372lsb

**Corts60** · 09-06-2020, 11:52 AM

Great work so far! Very nice stance.

08-31-2020, 09:25 AM	#26
Nick_R_23 Registered User Join Date: May 2016 Location: Willow, Alaska Posts: 894	Re: A freebie! 1986 C10 Longbed Something interesting! It’s a KEM engine rated at 304HP/396TQ.

08-31-2020, 04:10 PM	#28
Nick_R_23 Registered User Join Date: May 2016 Location: Willow, Alaska Posts: 894	Re: A freebie! 1986 C10 Longbed http://www.kemequipment.com/manuals/...r-curve-57.pdf

09-04-2020, 02:14 PM	#29
Nick_R_23 Registered User Join Date: May 2016 Location: Willow, Alaska Posts: 894	Re: A freebie! 1986 C10 Longbed Prepping the spindles for installation later today!

09-05-2020, 02:02 AM	#30
Nick_R_23 Registered User Join Date: May 2016 Location: Willow, Alaska Posts: 894	Re: A freebie! 1986 C10 Longbed Front end disassembled and being prepped for the new spindles! Cut 1 complete coil out of the spring, about 2” additional drop over the 2.5” spindles. Spring and spindle reinstalled. My dumb ass forgot to check the brake package before ordering the spindles...turns out this truck actually had the 1” rotors! So, perfect time to convert to JB5 rotors and calipers! Caliper and new pads installed! I’ll have to wait until tomorrow on the hoses, they ended up being a day out. Since the front end isn’t complete yet, enjoy another glorious rear end shot!

09-05-2020, 09:14 AM	#31
jjzepplin Registered User Join Date: Feb 2012 Location: Ruskin Florida Posts: 4,606	Re: A freebie! 1986 C10 Longbed Fancy indeed! Nothing wrong with a good rear shot. __________________ 70 swb 4x4 406sbc 700r4 203/205 d60/14blt locker yadda yadda http://67-72chevytrucks.com/vboard/s...88#post6935688 Yeller 72 Blazer 2wd conversion project "No Daggum Money" http://67-72chevytrucks.com/vboard/s...d.php?t=550804 LS1-T56 3.73 LSD super budget build Blanco-2014 Sierra SWB https://67-72chevytrucks.com/vboard/...d.php?t=810350

09-06-2020, 02:38 AM	#32
Nick_R_23 Registered User Join Date: May 2016 Location: Willow, Alaska Posts: 894	Re: A freebie! 1986 C10 Longbed Thanks! I finished up the driver side today with a new brake line! Completed the passenger side too! Installed the sway bar lowering brackets! Sway bar reinstalled! The front end is all back together! Back on all fours! This is perfection! Exactly what I was going for!

09-06-2020, 09:24 AM	#33
jjzepplin Registered User Join Date: Feb 2012 Location: Ruskin Florida Posts: 4,606	Re: A freebie! 1986 C10 Longbed That is very nice! Do you have any information on the kit you used? __________________ 70 swb 4x4 406sbc 700r4 203/205 d60/14blt locker yadda yadda http://67-72chevytrucks.com/vboard/s...88#post6935688 Yeller 72 Blazer 2wd conversion project "No Daggum Money" http://67-72chevytrucks.com/vboard/s...d.php?t=550804 LS1-T56 3.73 LSD super budget build Blanco-2014 Sierra SWB https://67-72chevytrucks.com/vboard/...d.php?t=810350

09-06-2020, 10:58 AM	#34
Nick_R_23 Registered User Join Date: May 2016 Location: Willow, Alaska Posts: 894	Re: A freebie! 1986 C10 Longbed Thank you! And yes, I do! Overall, this is about a 4.5” front/6” rear drop. Current tire size is 235/70R15, I will likely keep that front size and go 275/60R15 in the rear. The drop spindles are Classic Performance CLP-CP4s4 2.5” drop spindles. https://www.summitracing.com/parts/clp-cp4s4 The coil springs are stock 1/2 ton V8 springs with 1 complete coil cut as seen in the pictures, equal to about 2” additional drop. The rear leaf springs are the stock 3+1 spring pack, the overload spring is intact and no leafs were removed. The axle flip kit is UMI Performance UPI-6410, with a 6” drop. https://www.summitracing.com/parts/upi-6410 The shock extensions are UMI Performance UPI-6411. https://www.summitracing.com/parts/upi-6411 The sway bar relocation kit is Classic Performance CLP- 6372LSB. https://www.summitracing.com/parts/clp-6372lsb

09-06-2020, 11:52 AM	#35
Corts60 Just here to tinker Join Date: Jun 2008 Location: Holland, MI Posts: 3,698	Re: A freebie! 1986 C10 Longbed Great work so far! Very nice stance. __________________ 78 C10 SWB Diesel #1 (wrecked)http://67-72chevytrucks.com/vboard/s...1978+silverado 78 C10 SWB Diesel #2 (sold)http://67-72chevytrucks.com/vboard/s...d.php?t=650751 60 GMC Suburban (sold)http://67-72chevytrucks.com/vboard/s...d.php?t=445526 60 GMC 1000 (sold)http://67-72chevytrucks.com/vboard/showthread.php?t=298235 67 GMC 1500 (sold) http://67-72chevytrucks.com/vboard/s...d.php?t=803695 73 Chevy C20(Daily)http://67-72chevytrucks.com/vboard/s...d.php?t=852767 86 Suburban(summer unit) http://67-72chevytrucks.com/vboard/s...d.php?t=810697 88 Suburban 4x4(sold)



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.