CA WTB: 1967 Glove Box Door Emblem - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**mojavetrucker** · 03-24-2026, 05:03 PM

I’m looking for a decent used 1967 glove box emblem. I know there are reproductions available, but I was hoping to find one showing some patina that matched my 1967 K10 CST. I believe these had plastic studs that were melted to affix the emblem to the glove box door. I’m really not concerned about the studs still being present as I’ll probably just use some silicone to affix it to the door… I’m more concerned about the overall look.

Thanks for looking!

**1rippen6** · 03-24-2026, 07:21 PM

I may have one, I'll look tomorrow afternoon and let you know.

**mojavetrucker** · 03-24-2026, 07:25 PM

Quote:

Originally Posted by 1rippen6

I may have one, I'll look tomorrow afternoon and let you know.

Thank you, 1rippen6!

**1rippen6** · 03-25-2026, 11:42 AM

You're welcome. Here is what I have, it may too far gone for what you want.

**mojavetrucker** · 03-25-2026, 11:50 AM

Quote:

Originally Posted by 1rippen6

You're welcome. Here is what I have, it may too far gone for what you want.

Thank you again, 1rippen6...I'm going to pass on that one, but I really appreciate your reply and the time you took to send me a photo!

**70STOVEBOLT** · 03-26-2026, 09:40 PM

I have a repop you can apply the amount of patina to your liking.

**mojavetrucker** · 03-30-2026, 08:19 PM

Quote:

Originally Posted by 70STOVEBOLT

I have a repop you can apply the amount of patina to your liking.

Thank you, 70STOVEBOLT…I ended up finding an decent looking original emblem on eBay.

03-24-2026, 05:03 PM	#1
mojavetrucker Junior Member Join Date: Mar 2025 Location: Joshua Tree, CA Posts: 22	WTB: 1967 Glove Box Door Emblem I’m looking for a decent used 1967 glove box emblem. I know there are reproductions available, but I was hoping to find one showing some patina that matched my 1967 K10 CST. I believe these had plastic studs that were melted to affix the emblem to the glove box door. I’m really not concerned about the studs still being present as I’ll probably just use some silicone to affix it to the door… I’m more concerned about the overall look. Thanks for looking! Attached Images

03-24-2026, 07:21 PM	#2
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,912	Re: WTB: 1967 Glove Box Door Emblem I may have one, I'll look tomorrow afternoon and let you know.

03-25-2026, 11:42 AM	#4
1rippen6 Senior Member Join Date: May 2011 Location: Greencastle PA Posts: 6,912	Re: WTB: 1967 Glove Box Door Emblem You're welcome. Here is what I have, it may too far gone for what you want. Attached Images

03-26-2026, 09:40 PM	#6
70STOVEBOLT Senior Member Join Date: Jun 2005 Location: Winona Lake, IN Posts: 7,062	Re: WTB: 1967 Glove Box Door Emblem I have a repop you can apply the amount of patina to your liking. __________________ 70 C/10 SWB 402/TH400/3.73 "The Needy Beast" 200,000 Mile Club Disc Brake Club Owner installed options: Front Sway Bar Power Steering Power Brakes Cigar Lighter Courtesy Lights Deluxe Side Markers Wiper Delay Sliding Rear Window Power Windows Power Locks Sniper EFI 2015 Silverado 1500 LS 4.3/6L80/3.23 lowered 2" front & rear



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.