![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Post Whore
![]() Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,684
|
Steering column problem
In this pic of the steering column on my 70 K5 the area indicated by the area should be about 1" up. I was told this is the a race and there should be bearings.
Does anyone know what is involved in repairing this problem? Am I correct in assuming the vehicle shouldn't be driven with this problem? ![]()
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
![]() |
![]() |
![]() |
#2 |
Life is Good !
Join Date: Mar 2002
Location: Hollister, Ca.
Posts: 1,992
|
Picture is kind of dark.
![]() ![]()
__________________
'72 Chevy C10 4x4 shortbed "Project" '71 Chevy C10 2wd longbed "partsrunner" '91 Chevy Burb 4x4 "kidrunner" '14 Honda Accord Sport "commuter" |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jan 2003
Location: Emmett, Idaho
Posts: 858
|
Mark,
There is supposed to be a bearing there. Still available through GM, part #3981935, about $25 retail. I think it's also available aftermarket. Driving that way probably isn't the best/safest thing, but I've seen many like that going down the road. I stood outside last night waiting/listening for that thing to fire, looks like it may be cold this weekend ![]()
__________________
Larry 72 Chevy SWB 4x4 71 Chevy SWB 4x4 My Work Truck "Don't confuse enthusiasm with capability" |
![]() |
![]() |
![]() |
#4 |
Post Whore
![]() Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,684
|
Dang battery was too dead to fire the engine - will be picking up a replacement today, yep, it looks like it may be a cold weekend, well, cold for me at least!
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
hard to tell with the picture being so dark(a cheap clamp anywhere lamp makes pictures better) but yes there's supposed to be a bearing there and there's also supposed to be a spring above the clamp that holds the steering column to the intermediate shaft
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
![]() |
![]() |
![]() |
#6 |
Senior Member
Join Date: Nov 2003
Location: Brookings, SD
Posts: 10,497
|
I started reassembling my column last night, and there should be a metal retainer held on by a clip, then the bearing, and the bearing should be seated into a large plastic seat. It is real easy to replace.
I have the instructions in my assembly manual if you need them. Shawn
__________________
Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs. |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jan 2003
Location: Emmett, Idaho
Posts: 858
|
I'm not sure, but I think the tilt column end has the metal cup and retainer clip you're talking about. As Cdowns mentioned the standard column pictured uses a large washer and spring to keep the bearing in place.
__________________
Larry 72 Chevy SWB 4x4 71 Chevy SWB 4x4 My Work Truck "Don't confuse enthusiasm with capability" |
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: Nov 2003
Location: Brookings, SD
Posts: 10,497
|
You are right, I didn't even think about that. I should have paid more attention to the other replies.
__________________
Some people are like slinkies, they aren't good for anything, but you can't help but smile when you see one tumble down the stairs. |
![]() |
![]() |
![]() |
#9 |
Post Whore
![]() Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,684
|
Here's a lightened up photo - this is a photo I took of the engine compartment when I wasn't aware of the problem.
![]()
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
![]() |
![]() |
![]() |
#10 |
Post Whore
![]() Join Date: Feb 2000
Location: Rose Hill, KS, USA
Posts: 12,684
|
I have a three speed manual column I can probably grab parts off of to make this one work - this manual column is for a 4 speed on the floor.
__________________
1970 Blazer with a 400 sbc and 4" lift 1980 Pontiac Trans Am, 455 Oldsmobile 2012 Kawasaki Concours 14 |
![]() |
![]() |
![]() |
#11 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Lots of trucks are like this, there really is no danger in driving it. The steering wheel is still hooked to the gear box with a metal shaft.
|
![]() |
![]() |
![]() |
Bookmarks |
|
|