The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board

Web 67-72chevytrucks.com


 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 01-16-2012, 12:47 AM   #1
el_guapo
Registered User
 
Join Date: Dec 2010
Location: colorado springs
Posts: 126
Cool Dropping a square write up/ insights.

Before I begin I would like to thank Jknight for sharing his lowering method. Also big thank you to my boy Mike who really helped with the install. If it weren't for him I'd still be killing myself with the spindles. Haha
Before shots


After

Notice the tijuana interior. Haha


Newer members wanting to learn about dropping their trucks this write up is for you. I will give you an idea of the proccess and share some tips I would use next install. This is a cheap and relatively easy way to go about it. It involves dropping the front end by replacing the spindles and cutting the springs. This has not made a significant difference in the rides quality. Too much chopping up front will.

I ordered a DJM 5" flip kit. And 2.5" lowering spindles. I cut a little more than half of a coil. the front dropped aprox. 3.5" Under 350 shipped from Stylintrucks.com

Using 15" cragers I did run into fitment issues. I had to grind an edge off of the caliper and run washers as spacers. 15's are just while I can buy bigger wheels and to avoid knocking more metal off the calipers. We measured for backspacing on the wheels 3.75 or less is what would be needed to run ur wheels with no modifications.

For those curious this took a solid weekend I'd say 6-8 hours all together. An angle grinder a buddy a couple Jacks and jack stands. The factory spindles were pretty tough take off, the press fitment made it a chore. Other than that the front was straight forward.

Taking the spindles off, man love needed to pry off.

Old vs new spindle

Marking coils. Cut 5/8ths of a coil.

magic


You will need to do some re-greasing Btw

Big booty hoe


The rear went well, we did run into issues with the leafs bolts being crazy tight. We actually disconnected brake lines and managed to fit the axle in between the frame and leafs in order to place the leafs packs under the axle. haha. We pried on the rear of the springs to make the leafs bend enough to fit the drums through.

Angle grinder vs bump stop, I wasn't drunk just looking away because I couldn't find my glasses. This was needed to fit the drums through the leafs/frame.


Next time to pry on the leaf hangers from the back to make room

It's in on one side!

This was a creative alternative to disconnecting the leafs. Unfortunately the rears bushings and bolt have united and become one over time. Haha, The rear wasn't coming with out cutting the bolt/bushing. We did not have enough room to disconnect the pack from the front. Not enough room for a breaker bar plus cheater bar. We did also disconnect the driveshaft for this method.


She's in there like swimwear

Again big thank you to Mike and also these boards for always pointing me in the right direction.
Anthony Z
Posted via Mobile Device

Last edited by el_guapo; 01-16-2012 at 01:10 AM.
el_guapo is offline   Reply With Quote
 

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:12 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com