The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 11-13-2016, 09:42 PM   #1
Boeing
Registered User
 
Join Date: Oct 2016
Location: Calgary, Alberta
Posts: 26
what is required for PCM pinouts

Ok, so this is a tall order, so big thanks in advance. These are the correct connections for my PCM with my 1995 5.7 liter. I am trying to thin out the factory harness. My question is: what do i need to just make this engine run and go down the road? I get the easy stuff, power, ground, injectors etc.
but what about O2 sensors and egr connections, things like that?
I will not be running any kind of emissions stuff that I dont need, unless of course its required to keep the engine running.

Thanks guys




RED PCM 32 Pin Connector
Pin Wire Color Description
A-1 BLK/WHT PCM Ground
A-2 TAN/WHT PCM Ground
A-3 LT BLU/WHT Idle Air Control (IAC) Valve “A” High
A-4 PPL/WHT Ignition Control Module REF High
A-5 RED/BLK Ignition Control Module REF Low
A-6 LT BLU/BLK Idle Air Control (IAC) Valve “A” Low
A-7 LT GRN/BLK Idle Air Control (IAC) Valve “B” Low
A-8 LT GRN/WHT Idle Air Control (IAC) Valve “B” High
A-9 DK GRN Fuel Injector “B”
A-10 PPL Oxygen Sensor Signal
A-11 --- Empty
A-12 TAN Oxygen Sensor Ground
A-13 --- Empty
A-14 WHT/BLK DLC Diagnostic
A-15 DK BLU TP Signal
A-16 DK BLU Fuel Injector “A”
B-1 --- Empty
B-2 TAN/BLK Ignition Control Module Bypass
B-3 BLK Sensor Ground
B-4 BLK Sensor Ground
B-5 YEL/BLK Transmission Fluid Temp
B-6 --- Empty
B-7 --- Empty
B-8 YEL ECT Sensor Signal
B-9 --- Empty
B-10 LT BLU/BLK Cruise Control
B-11 --- Empty
B-12 GRY Fuel Pump Signal
B-13 LT GRN MAP Sensor Signal
B-14 --- Empty
B-15 DK BLU Knock Sensor
B-16 BRN EGR Pintle


-------BLUE CONNECTOR-----------------------------------------------------------

Pin Wire Color Description
E-1 GRY EGR Solenoid
E-2 WHT 3-2 Shift Control Solenoid
E-3 --- Empty
E-4 DK BLU Range Signal B
E-5 RED Range Signal C
E-6 BRN/WHT Check Engine Light (CEL)
E-7 --- Not Used
E-8 YEL/BLK 2-3 Shift Solenoid Enable
E-9 LT GRN 1-2 Shift Solenoid Enable
E-10 TAN/BLK TCC Solenoid (w/ 4L60-E Only)
E-11 BRN TCC Solenoid (w/ 4L60-E Only)
E-12 DK GRN A/C Request
E-13 PPL Brake Switch
E-14 GRY 5 Volt Ref (MAP, Linear EGR)
E-15 PNK IGN Fused
E-16 ORN Battery Feed
F-1 PNK Range Signal A
F-2 RED/BLK Trans Input Shaft Speed Sensor (+)
F-3 DK BLU/WHT Trans Input Shaft Speed Sensor (-)
F-4 --- Empty
F-5 --- Empty
F-6 DK GRN/WHT Fuel Pump Relay Control
F-7 LT BLU/WHT Pressure Control Solenoid “Low”
F-8 GRY/BLK 4WD Switch
F-9 TAN Serial Data
F-10 RED/BLK Pressure Control Solenoid “Hi”
F-11 WHT Ignition Control Module Signal
F-12 BRN Transmission Output Speed
F-13 DK BLU VSS Signal
F-14 GRY 5 Volt Sensor Reference Voltage (TPS, MAP)
F-15 PNK IGN Feed
F-16 DK GRN/WHT Canister Purge Solenoid
Boeing is offline   Reply With Quote
 

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:55 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com