Install and Review of Dapper Lighting OE7 LED Headlights

[fastpace]

Just had one of the sealed halogen bulbs burn out on my 72 C10 so I searched the forum to see what kinds of options were available. From my searches I found you have the following options:

• Halogen sealed beam direct replacement - ~$50, suggested to add relays to improve voltage and light output
• Halogen H4 Conversion - ~$100, suggested to add relays and then some swap to xenon bulbs to maximize light output. Total package ~$200
• HIDs - ~$300-600 lots of different options, has a more modern look, normally requires additional wiring for the ballasts
• LEDs - ~$300-600 again a lot of options, but there's more flexibility in the glass and ability to look closer to stock

I prefer to have something that has a stock look and then stumbled on Dapper Lighting OE7 bulbs which maintain glass with reflector cuts for a stock look on most of the bulb. https://www.dapperlighting.com/products/oe7

Given the price point being just a little over the next best option for the stock look (H4 conversion, relays, and xenon bulbs) but a simpler install and potentially improved light output and life I decided to give them a shot. They've done some advertisement posts on the forum but couldn't find much info on the install fit and final results so thought I'd put something together.

I ended up ordering the OE7 with the OE Glass style ($50 option for the stock reflector cuts otherwise the glass is smooth) and White Phillips Daytime running lights ($13 option that I don't think I'm going to end up wiring) for a total of $386.58 shipped to me in Houston.

The box arrived and was nicer than just your average brown box. Bulbs were well packaged to ensure they arrived undamaged


After taking them out, the overall housing and glass looks nice. I was a little disappointed in the back of the housing is plastic, but at least the front is actual glass so should hold up and last.


With the 3 prong plug, it's a direct plug and play option


To start the install, the bezel need to be removed by removing the 4 phillips head screws.


Then you can get to the 3 flat head screws to remove the bulb ring. The other phillips are for aiming your headlights so if your lights were aimed well before hopefully you won't need to touch them.


With the ring removed the old bulb should come right out and just have the empty headlight bucket


When you go to install the OE7, it's labeled for the top of the bulb which will help have your alignment tabs fall right and it also looks like there is a difference in the internal deflectors and bulb install. Also puts the day time running light bulb at the bottom.


In order to get the bulb to fit you'll need to roll the rubber boot back to get it to fit through the hole in the headlight bucket. It's a tight fit, but no modification is need which was really nice to see.


Then you can roll the rubber boot back down and it'll hold the bulb in place for you.


This gives you the opportunity to check the alignment tabs are sitting in place and then you can reinstall the ring and trim.


With it all buttoned back up, plug them it in and turn them on to test.




After install I had to get some comparison pictures. I used my phone on the Pro mode and fixed the aperture, ISO, and exposure time so that the pictures could be used for comparison without variation of exposure. All pictures are low beams because the high beam filament is burnt out on the halogen. First, pictures from the interior of the truck.
Halogen


OE7


Both


Then some pictures looking back at the lights
Halogen


OE7


Both


Finally, a picture from the front of the truck which really shows the difference in the light spread and cutoff line of the OE7.


Overall, I liked the fact that it was a simple install and plug in, no modifications required. I chose not to wire in the DRL for now but I might consider it later but I don't think they add much benefit. From the pictures you can clearly see there is a big difference between the halogens and the OE7 especially with respect to area coverage. The temperature of the light is much nicer and will help be able to see things versus the warm color of the halogens. I'm satisfied with the results and look forward to the next night time drive to put them to work.