|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
01-15-2005, 06:47 AM
|
#1 |
|
Senior Member
Join Date: Aug 2002
Location: Plymouth, MA
Posts: 891
|
Will a Cab fit in a long bed?
I bought a cab a few weeks ago and since I am overseas, my dad or brother is going to pick it up for me. What I need to know is, if they will have to get a trailer or if it will fit in the bed of a longbed pick-up. Thanx
__________________
1972 Blazer body...need to get a thread started for the rest of the story |
|
|
|
01-15-2005, 07:03 AM
|
#2 |
|
Senior Member
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
|
Yes, the cab will fit in a long bed quite nicely. It has to be turned sideways
and centered over the wheel wells. If the rockers are good, then it can be supported with approximately 5" high pallets. If the cab still has the outside heater housing it will need to clear the side. Check the measurements on this but as I remember it will clear with a 5" pallet under the rockers. If the rockers won't support it the cab rails can be used and the necessary cribbing added. We strapped the cab in place as we trucked it for over a hundred miles and did not want it shifting. Jim |
|
|
|
|
01-15-2005, 07:17 AM
|
#3 |
|
Registered User
 
Join Date: Apr 2004
Location: The Other Maine!
Posts: 2,236
|
I did this without any problems as well!
__________________
1968 Chevy 4x4 307 4 speed |
|
|
|
|
01-15-2005, 07:33 AM
|
#4 |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,690
|
it'll fit in a SWB...I carried mine up from Tx that way
|
|
|
|
|
01-15-2005, 09:08 AM
|
#5 |
|
user # 2756
Join Date: Jun 2001
Location: Chesapeake, Virginia
Posts: 4,612
|
I've done this too, except I was getting rid of the cab off of my 71.
__________________
1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm 
|
|
|
|
|
01-15-2005, 11:54 AM
|
#6 |
|
Senior Member
Join Date: Apr 2001
Location: Amazonia, Mo. USA
Posts: 2,821
|
__________________
72 3/4 4x4 350 4spd 72 3/4 4x4 350 auto 2004 Duramax Silverado 4x4 2006 Duramax Crew cab 4x4 2010 Harley Ultra Limited 2011 Harley Street Glide |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
