WTB: Bed Floor Pieces - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Huskerboy2 · 02-19-2005, 12:56 AM

Somebody out there has got to have a trashed bed somewhere. I am looking for some patch panels out of a bed floor. I need the area around the wheel well opening on the drivers side, the half or so closest to the front. I also need a few inches on each side of the rear edge. Anybody?? I know where there are a couple of good bed floors, but I can't bring myself to cut them up just for a couple of square feet of patches.

GMC AMI · 02-19-2005, 01:21 AM

How about the patch panels J. C. Whitney sells with the correct ribs? Maybe a board vendor?

LUV2XCLR8 · 02-19-2005, 09:12 AM

Quote:

Originally Posted by Mike Files

Maybe a board vendor?

I KNOW TIM HAS EM

www.christiansclassics.com

MOTHERTRUCKERS · 02-19-2005, 10:08 AM

The new 48x16 floor patches are under 25.00 each in most catalogs

Huskerboy2 · 02-19-2005, 11:25 AM

I'll probably end up going that route. I just didn't want to have to fab that rear lip and the tapered ends on the ribs at the back of the floor-although I guess it wouldn't be too hard. My bed floor is really solid, except for two quarter sized rust holes at the rear edge on each side and just a couple of inches around the wheel well opening. I want to save 99% of my existing bed. The patch panels that I have seen are just the ribs, not the finished area at the back of the bed. I don't want to murder a good bed floor just for these pieces.

Huskerboy2 · 02-19-2005, 11:25 AM

By the way, thanks for the replies guys.

02-19-2005, 12:56 AM	#1
Huskerboy2 Senior Member Join Date: Feb 2001 Location: Austin, Texas, USA Posts: 1,628	WTB: Bed Floor Pieces Somebody out there has got to have a trashed bed somewhere. I am looking for some patch panels out of a bed floor. I need the area around the wheel well opening on the drivers side, the half or so closest to the front. I also need a few inches on each side of the rear edge. Anybody?? I know where there are a couple of good bed floors, but I can't bring myself to cut them up just for a couple of square feet of patches. __________________ '72 Chevy Blazer

02-19-2005, 01:21 AM	#2
GMC AMI Registered User Join Date: Apr 2004 Location: The Other Maine! Posts: 2,236	How about the patch panels J. C. Whitney sells with the correct ribs? Maybe a board vendor? __________________ 1968 Chevy 4x4 307 4 speed

02-19-2005, 10:08 AM	#4
MOTHERTRUCKERS Registered User Join Date: Dec 1999 Location: BRADENTON FLA Posts: 3,269	The new 48x16 floor patches are under 25.00 each in most catalogs __________________ Rest in Peace Ed. Thanks for all the good times.

02-19-2005, 11:25 AM	#5
Huskerboy2 Senior Member Join Date: Feb 2001 Location: Austin, Texas, USA Posts: 1,628	I'll probably end up going that route. I just didn't want to have to fab that rear lip and the tapered ends on the ribs at the back of the floor-although I guess it wouldn't be too hard. My bed floor is really solid, except for two quarter sized rust holes at the rear edge on each side and just a couple of inches around the wheel well opening. I want to save 99% of my existing bed. The patch panels that I have seen are just the ribs, not the finished area at the back of the bed. I don't want to murder a good bed floor just for these pieces. __________________ '72 Chevy Blazer

02-19-2005, 11:25 AM	#6
Huskerboy2 Senior Member Join Date: Feb 2001 Location: Austin, Texas, USA Posts: 1,628	By the way, thanks for the replies guys. __________________ '72 Chevy Blazer

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.