![]() |
![]() |
#1 |
Registered User
Join Date: Oct 2003
Location: Cumming, Ga
Posts: 234
|
tight ujoint
Bad news - Drive shaft fell out.
Good news - doesnt appear to be damaged. I got a new rear u joint and installed it. But it appears to be really tight when I put it back on. Ive taken it off and done it again but cant seem to get it on to where it just flops around. Any iders or suggestions from before? Glenn
__________________
Glenn Cumming, Ga (68 C/10 Fleetside LWB 307 (64 C/10 Fleetside Shorty Custom 350, with 73 donor parts aplenty) (2001 Porsche Boxster S - 168 MPH of fun) (2005 Chevy Avalanche Z71 1500) |
![]() |
![]() |
![]() |
#2 |
Account Suspended
Join Date: Mar 2003
Location: ** THE FALL GUY **CHICAGO IL
Posts: 5,883
|
one of the bearings is not right....
![]() ![]() |
![]() |
![]() |
![]() |
#3 |
Still drivin' a Rat Rod
Join Date: Sep 2004
Location: Monett Missouri
Posts: 4,925
|
Yup.make sure one of the needle bearings isn't laying in the bottom of the cap.Did that myself recently,being in a hurry doesn't pay off for me
![]()
__________________
Rusty Member #13872 Instead of saying.....you are a discomfort in the back of my front.....one should be able to say...... you are a pain in the *a$#* 71 GMC LWB 49 Chevy 85 Chevy G20 Check out my website |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Aug 2001
Location: rock island,il,usa
Posts: 5,382
|
any little dent/ding will put the shaft out of balance....you might try seating the caps against the retainer rings (just thump the ends of the shaft with a lead hammer).....not on the tube tho!
__________________
http://community.webshots.com/user/hotrodhorn |
![]() |
![]() |
![]() |
#5 |
Sisyphus was my mentor!
![]() Join Date: Sep 2002
Location: Carleton Place, Ontario CANADA
Posts: 984
|
Is it the type of u-joint that the snap ring goes in a groove on the outside rather than the inside? If there isnt a needlebearing trapped in there some where & if it is the type that the snap ring goes in a groove on the outside then it may just be a tight fit. You can lightly sand the back of the cap that butts up against the snapring to increase clearance.
__________________
passthebuck ![]() #5642 -TWO 1967 GMC 910's. One with L6/3-on-the tree and the other with 355 w/435hp & a 700r4. -a 2013 Honda Civic as my "sensible" car |
![]() |
![]() |
![]() |
#6 |
Still drivin' a Rat Rod
Join Date: Sep 2004
Location: Monett Missouri
Posts: 4,925
|
Could be the yoke is bent slightly,I hope not,but as you said it fell out.
__________________
Rusty Member #13872 Instead of saying.....you are a discomfort in the back of my front.....one should be able to say...... you are a pain in the *a$#* 71 GMC LWB 49 Chevy 85 Chevy G20 Check out my website |
![]() |
![]() |
![]() |
#7 |
Senior Member
![]() Join Date: Feb 2003
Location: WIS
Posts: 1,752
|
tight
The bearing cups are pressed too far in. Tap (hard) on the bearing retainer near where it's welded to the tube. (not the tube like stated earlier). Make sure you hammer at the correct indexing location. You want the bearing cups to be pushed back out a few thousandths. Not the cups that are in the differential yoke. The other pair.
|
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Oct 2003
Location: Cumming, Ga
Posts: 234
|
Will look closer tonight.
__________________
Glenn Cumming, Ga (68 C/10 Fleetside LWB 307 (64 C/10 Fleetside Shorty Custom 350, with 73 donor parts aplenty) (2001 Porsche Boxster S - 168 MPH of fun) (2005 Chevy Avalanche Z71 1500) |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Oct 2003
Location: Cumming, Ga
Posts: 234
|
It was a needle bearing issue. I replaced the whole unit and now she's running like she was new! Thanks for the response!
![]()
__________________
Glenn Cumming, Ga (68 C/10 Fleetside LWB 307 (64 C/10 Fleetside Shorty Custom 350, with 73 donor parts aplenty) (2001 Porsche Boxster S - 168 MPH of fun) (2005 Chevy Avalanche Z71 1500) |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|