![]() |
![]() |
#1 |
Registered User
![]() Join Date: Feb 2005
Location: S.E. South Dakota
Posts: 161
|
Brake Line Question?
Does anyone know how to clean up brake lines, to make them look new again? Can you sandblast or use some sort of cleaner? Thanks
![]() |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
|
![]()
Steel brake lines are zinc coated and if you use any abrasive on the lines it will remove the coating and hasten the corrosion process. I would just wash them with solvent.
Jim |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Nov 2003
Location: Alexandria, VA
Posts: 1,534
|
Don't sandblast your brake lines, it wouldn't be worth the risk of getting silica into the system and ruining everything. Replace all your lines with new steel/stainless steel tubing since the originals are 35+ yrs old and are probably corroded internally. The NAPA here sells it in various lengths already flared on both ends with fittings, you can buy a decent tubing bender and make a new set yourself. The spring material is available from www.inlinetube.com or www.rightstuffdetailing.com
__________________
'72 GMC SWB C1500 Custom, frame-off in progress. 383 SBC, 9:1CR, Comp Cams XE262H, Scat internal balanced crank, Eagle SIR 6" rods, Keith Black dish pistons, Dart Iron Eagle 72/180 heads, Weiand Stealth intake, Stewart stage I water pump, Holley 4bbl vac sec, TH350 with B&M Shift Improver Kit. 12 bolt positraction. ![]() ![]() ![]() Last edited by Sweet72; 03-28-2005 at 08:51 PM. |
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: Feb 2005
Location: S.E. South Dakota
Posts: 161
|
Thanks for the info. What would you recommend going with steel lines or stainless steel? Thanks
|
![]() |
![]() |
![]() |
#5 |
Registered User
![]() Join Date: Sep 2001
Location: Cumming, GA
Posts: 471
|
I purchased the inline tube kit (steel) and they fit perfectly with no mods required. Stainless will look better, but who's looking at your brake lines?
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Nov 2004
Location: Dover, AR
Posts: 120
|
I have used steel wool before to clean them with, and then just used some cheap rattle can clear to spray over them, looks pretty good.
__________________
was 67 chevy swb fleet now muticolored 69 step, 350/350, 3.73 posi, converted to 5 lug, torq thrust II 17x8 front 17x9.5 rear, factory air cab, fuel cell. future plans: shaved wiper cowl, shave stake pockets, phantom grille, and silver paint... 68 camaro ss396 project 54 f*rd project truck |
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Nov 2000
Location: Huntsville Ontario Canada
Posts: 4,052
|
If you do them in stainless you will never have to look at them again.
__________________
1968 Suburban numbers matching all original truck now equipped with 6.0/4L80 on Accuair http://67-72chevytrucks.com/vboard/s...d.php?t=625017 1967 C/20 6.0/4L80 Roofing Truck 1990 V2500 Suburban "Plow Truck" 2005 TAHOE DD |
![]() |
![]() |
![]() |
#8 | |
Registered User
Join Date: Oct 2002
Location: S.W. Michigan
Posts: 403
|
Quote:
If you do them in stainless you will want to look at them again. They will be purddy. ![]() Dan |
|
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Sep 2003
Location: Evergreen, CO
Posts: 494
|
"Anything worth doing yourself is worth doing in stainless..."
... and I'm pretty good at spending other peoples money. |
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Nov 2003
Location: Alexandria, VA
Posts: 1,534
|
I bought a stainless set including the front/rear hoses and clips from the right stuff detailing. You can get the brass flare fitting unions and tees from your NAPA. I definitely recommend the stainless lines without a doubt. One note on the stainless lines though that no-one has mentioned...the fittings on the pre-made lines are regular plated steel and WILL CORRODE when exposed to the elements!
__________________
'72 GMC SWB C1500 Custom, frame-off in progress. 383 SBC, 9:1CR, Comp Cams XE262H, Scat internal balanced crank, Eagle SIR 6" rods, Keith Black dish pistons, Dart Iron Eagle 72/180 heads, Weiand Stealth intake, Stewart stage I water pump, Holley 4bbl vac sec, TH350 with B&M Shift Improver Kit. 12 bolt positraction. ![]() ![]() ![]() |
![]() |
![]() |
![]() |
#11 |
I'm watching you!
Join Date: Feb 2005
Location: Levittown, PA
Posts: 1,822
|
Just ordered my truck a set of stainless pre-bent lines
![]() ![]() Mike
__________________
2012 Chevrolet Silverado 1500 Z71 4WD 1993 Chevrolet C-1500 W/T - Blue - 4.3L V-6, 4 speed auto - Dad's (RIP) 1992 Chevrolet S10 - LS swap project 1968 Chevrolet C-10 longbed fleetside - sold ![]() |
![]() |
![]() |
![]() |
#12 |
Registered User
Join Date: Dec 1999
Location: BRADENTON FLA
Posts: 3,269
|
I have a set of front power brake stainless inline tube for a 71 half ton 40.00 + shipping, new in the torn package. NO GUARANTEE ON THE FIT. I gave up and made my own.
__________________
Rest in Peace Ed. Thanks for all the good times. |
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: Nov 2000
Location: Huntsville Ontario Canada
Posts: 4,052
|
Check Summit they sell stainless flare tube nuts for brake and fuel lines.
__________________
1968 Suburban numbers matching all original truck now equipped with 6.0/4L80 on Accuair http://67-72chevytrucks.com/vboard/s...d.php?t=625017 1967 C/20 6.0/4L80 Roofing Truck 1990 V2500 Suburban "Plow Truck" 2005 TAHOE DD |
![]() |
![]() |
![]() |
#14 |
Senior Member
![]() Join Date: Mar 2001
Location: Cedar Park, TX
Posts: 686
|
the ones inline tube sells includes the metal end fittings in stainless as well.
__________________
71 Chevy C-10 SWB Fleetside RamJet-350/4L60e & Compushift/3.73Posi See it at www.prismnet.com/~grzanich |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|