What was the hardest part for you to find?? - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

teamharvey · 04-10-2005, 10:08 PM

Quote:

Originally Posted by pound41

Teamharvey:
Is it the wire or just the wire end? Usually its the end that goes bad. You can take the old end apart and mount it to a new wire/or old one again. Also I have taken just a standard plastic coated female wire end cut a little channel on the backside and slide it on

I need the entire wire

wright-ons · 04-11-2005, 03:37 PM

Had lots of trouble finding a complete set of sun visors. Finely found a set but got bent over. If you have a cheep set please don't tell me

LUV2XCLR8 · 04-11-2005, 04:15 PM

WRIGHT-ONS -

2 THE BOARD FROM WEST 10-UH-C

3wbdriver · 04-19-2005, 10:20 PM

Hatch hardware! Any hatch hardware. All I've got is 2 very sloppy hinges and the lift slides. The hatch is holding itself closed by weight only.

wingman · 04-20-2005, 08:13 AM

I also cant find the hatch hinges and hardware. Also a fan shroud I can seem to find the right size one and im not paying $100 for a new one that is bull, but luckily i dont overheat, I just have to watch out for the fan when im working on it.

**D.PASSMORE** · 04-20-2005, 02:26 PM

If your looking for a 4x4 fan shroud; GMPARTSDIRECT / $50.00.

Davy · 04-20-2005, 02:38 PM

Quote:

Originally Posted by D.PASSMORE

If your looking for a 4x4 fan shroud; GMPARTSDIRECT / $50.00.

Do you happen to have the part number? $50 is a deal.

LUV2XCLR8 · 04-20-2005, 03:33 PM

Some extra hatch hardware, circled in red, see the pic's

(currently at the sandblaster, will be back soon I hope)

wingman · 04-20-2005, 06:27 PM

The pn is GM PART # 3951922 can anyone verfiy this is the right part for our trucks (4x4 are the deep ones correct?). If so I will definiatly be ordering one this week. Now if only i could find some hatch hinges and maybe just a complete hatch since my lock part is broken off and missing....

*Gee_Emm* · 04-20-2005, 06:50 PM

Here figure it out yourself

3 on the tree · 04-20-2005, 10:30 PM

So, my 250/3 speed standard cooling did not come with a shroud in 70?

pound41 · 04-21-2005, 07:09 AM

It would have come with the smaller shroud that I have seen on most 6cyl like the one I had on my 292/4speed

3 on the tree · 04-21-2005, 09:45 AM

All I have is the small steel piece bolted above the rad, and I see no evidence of anything else ever being attached.

pound41 · 04-21-2005, 02:25 PM

If its slighty curved the best way I can describe it would be something similar on a tractor thas it. some had some for sale on parts board the other day try looking they had pics

cleszkie · 04-21-2005, 03:18 PM

Took me a while to find a complete set of 3/4 ton, 4x4, chrome dog dish hubcaps with the correct blue bowtie. Found em out in the Cali desert at some podunk hubcap shack. Actually found two with the front hub cut outs, and three for the rear. Bought em all!

HatGuy · 04-27-2005, 06:56 AM

1. The metal strips and rubberweather strip
that runs up & down each side of the tub
where the tailgate fits.

2. Bumpers on the console near the front on
each side where the lid touches the main
part of the console.

71jimmy · 04-27-2005, 12:18 PM

The rubber strips for the side of the tailgate/tub are reproduced, it's the metal piece that runs inside the rubber strip that is not reproduced.

teamradrz1 · 04-27-2005, 10:27 PM

Quote:

Originally Posted by jamie72

a good hatch stop or the chrome single wall hold daown strips...

I found some at the Portland swap meet cheap to but my hands were full and I had never seen them before so I weren't sure if they would fit my single wall top.

HatGuy · 04-28-2005, 12:02 AM

I Did not see the rubber strips in the LMC catalog.
Any other places I might find them?

71jimmy · 04-28-2005, 02:32 AM

Try this link, I think it's item 17. http://www.****************.com/blaz...therstrip.html Give them a call, real nice people. I think I read somewhere else on here that Christians or one of the other Vendors that advertise on the board has them.

HatGuy · 04-28-2005, 04:33 AM

Thanks 71jimmy
Are they the same on pickups and Blazers/Jimmys?
The metal Strip that is.

71jimmy · 04-28-2005, 12:21 PM

I don't think pickups use them. No need to seal the rear.

04-11-2005, 04:15 PM	#28
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,468	WRIGHT-ONS - 2 THE BOARD FROM WEST 10-UH-C __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

04-19-2005, 10:20 PM	#29
3wbdriver Registered User Join Date: Aug 2003 Location: West Central Louisiana Posts: 82	Hatch hardware! Any hatch hardware. All I've got is 2 very sloppy hinges and the lift slides. The hatch is holding itself closed by weight only. __________________ '72 Blazer, 4WD, 350/4 spd. Affectionately known as "Da Beast" '04 Silverado (new daily driver) '00 Intrepid (wife's ride) It's a BLAZER dude! No options, no emblems, no a/c, no fancy shmancy. It's a BLAZER....

04-20-2005, 02:26 PM	#31
D.PASSMORE One of the First Join Date: Jan 2000 Location: St. Augustine,FL. Posts: 4,059	Fan shroud If your looking for a 4x4 fan shroud; GMPARTSDIRECT / $50.00. __________________ DAVID PASSMORE ST AUGUSTINE ,FL ZIP 32084 '71 SWB K/10 CUSTOM DELUXE (Chili) '72 BLAZER K/5 Muscle Truck (Mule) '72 LWB K/20 CHEYENNE (Blackie)

04-20-2005, 03:33 PM	#33
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,468	Some extra hatch hardware, circled in red, see the pic's (currently at the sandblaster, will be back soon I hope) __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T Last edited by LUV2XCLR8; 04-20-2005 at 03:34 PM.

04-27-2005, 06:56 AM	#41
HatGuy Registered User Join Date: Aug 2003 Location: Fort Worth Texas Posts: 275	1. The metal strips and rubberweather strip that runs up & down each side of the tub where the tailgate fits. 2. Bumpers on the console near the front on each side where the lid touches the main part of the console. __________________ Joe Peters the HatGuy 72' K5 Highlander My Daily Driver http://www.pbhats.com/BLAZER/index.html

04-11-2005, 03:37 PM	#27
wright-ons Registered User Join Date: Oct 2004 Location: Central CA Posts: 20	Had lots of trouble finding a complete set of sun visors. Finely found a set but got bent over. If you have a cheep set please don't tell me

04-20-2005, 08:13 AM	#30
wingman Registered User Join Date: Apr 2005 Posts: 41	I also cant find the hatch hinges and hardware. Also a fan shroud I can seem to find the right size one and im not paying $100 for a new one that is bull, but luckily i dont overheat, I just have to watch out for the fan when im working on it.

04-20-2005, 06:27 PM	#34
wingman Registered User Join Date: Apr 2005 Posts: 41	The pn is GM PART # 3951922 can anyone verfiy this is the right part for our trucks (4x4 are the deep ones correct?). If so I will definiatly be ordering one this week. Now if only i could find some hatch hinges and maybe just a complete hatch since my lock part is broken off and missing....

04-20-2005, 06:50 PM	#35
Gee_Emm Account Suspended Join Date: Sep 2000 Posts: 3,991	Here figure it out yourself

04-20-2005, 10:30 PM	#36
3 on the tree Registered User Join Date: Oct 2004 Posts: 392	So, my 250/3 speed standard cooling did not come with a shroud in 70?

04-21-2005, 07:09 AM	#37
pound41 Registered User Join Date: Dec 2002 Location: Northern Virginia Posts: 1,268	It would have come with the smaller shroud that I have seen on most 6cyl like the one I had on my 292/4speed

04-21-2005, 09:45 AM	#38
3 on the tree Registered User Join Date: Oct 2004 Posts: 392	All I have is the small steel piece bolted above the rad, and I see no evidence of anything else ever being attached.

04-21-2005, 02:25 PM	#39
pound41 Registered User Join Date: Dec 2002 Location: Northern Virginia Posts: 1,268	If its slighty curved the best way I can describe it would be something similar on a tractor thas it. some had some for sale on parts board the other day try looking they had pics

04-21-2005, 03:18 PM	#40
cleszkie Registered User Join Date: Feb 2003 Location: Santa Ana, CA Posts: 2,191	Took me a while to find a complete set of 3/4 ton, 4x4, chrome dog dish hubcaps with the correct blue bowtie. Found em out in the Cali desert at some podunk hubcap shack. Actually found two with the front hub cut outs, and three for the rear. Bought em all!

04-27-2005, 12:18 PM	#42
71jimmy Registered User Join Date: Mar 2004 Location: Sacramento, CA Posts: 1,083	The rubber strips for the side of the tailgate/tub are reproduced, it's the metal piece that runs inside the rubber strip that is not reproduced. __________________ '71 Jimmy, 350, SM465, NP205, 2in Tuff Country lift, 33s on rallies, TBI, softtop and hardtop "If life was fair you'd be able to afford one of each and a garage large enough to house them all."



Register or Log In To remove these advertisements.

04-28-2005, 12:02 AM	#44
HatGuy Registered User Join Date: Aug 2003 Location: Fort Worth Texas Posts: 275	I Did not see the rubber strips in the LMC catalog. Any other places I might find them? __________________ Joe Peters the HatGuy 72' K5 Highlander My Daily Driver http://www.pbhats.com/BLAZER/index.html

04-28-2005, 02:32 AM	#45
71jimmy Registered User Join Date: Mar 2004 Location: Sacramento, CA Posts: 1,083	Try this link, I think it's item 17. http://www.****************.com/blaz...therstrip.html Give them a call, real nice people. I think I read somewhere else on here that Christians or one of the other Vendors that advertise on the board has them. __________________ '71 Jimmy, 350, SM465, NP205, 2in Tuff Country lift, 33s on rallies, TBI, softtop and hardtop "If life was fair you'd be able to afford one of each and a garage large enough to house them all."

04-28-2005, 04:33 AM	#46
HatGuy Registered User Join Date: Aug 2003 Location: Fort Worth Texas Posts: 275	Thanks 71jimmy Are they the same on pickups and Blazers/Jimmys? The metal Strip that is. __________________ Joe Peters the HatGuy 72' K5 Highlander My Daily Driver http://www.pbhats.com/BLAZER/index.html

04-28-2005, 12:21 PM	#47
71jimmy Registered User Join Date: Mar 2004 Location: Sacramento, CA Posts: 1,083	I don't think pickups use them. No need to seal the rear. __________________ '71 Jimmy, 350, SM465, NP205, 2in Tuff Country lift, 33s on rallies, TBI, softtop and hardtop "If life was fair you'd be able to afford one of each and a garage large enough to house them all."

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.