My bell crank broke. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

pritch · 08-27-2005, 08:53 PM

30 miles from home, but just pulling away from the last stoplight I would have to stop for before home. I pushed in the clutch for third gear and something snapped and the clutch pedal went to the floor and I just kept on going. Someone pulled out in front of me and I had to downshift into 2nd with no clutch and then back into 3rd, but I never had to stop all the way home.

So now I need a new bellcrank. Is there any difference in them between the I6 and the SBC? I think I have one around here somewhere, but it came out of a V8 truck.

*Randy70C-10* · 08-27-2005, 09:12 PM

Nope, no difference

69 longhorn · 08-27-2005, 09:39 PM

Yes they are different (I6 or v8). you need the 6 pc, or if you have all the pcs,you can Have a local welder "fix" the problem. crazyL

pritch · 08-27-2005, 10:40 PM

Looks like differing opinions

I didn't know what broke when it broke, I didn't think it was a good idea at the time to stop and see, so no, I don't have the piece that broke off

I may just have to plan a trip to the junk yard to find one off a 6. No big deal, I just can't do it tomorrow.

**hotrodmtodd** · 08-27-2005, 10:44 PM

I will swap you one for a 6 for that V-8 one if you want. OR I can just send you out one on MON if you need it BAD. Let me know with a PM if you need it. Good luck, Mike

69 longhorn · 08-27-2005, 10:57 PM

it looks like you may need the bottom rod , from the bellcrank to the throw out fork also. best of luck,crazyL

**'68OrangeSunshine** · 08-28-2005, 06:02 AM

The V8 Z-bar is 7" across and the L6 Z-bar is 5-13/16th inches.

pritch · 08-28-2005, 07:27 PM

Well, my buddy had one up in his boneyard. All fixed and back together. Except I still need that little widget that goes on the clutch end of the push rod. The thing that actually touches the throw out arm. I just put a big flat washer on it for now, but I want the correct part.

**hotrodmtodd** · 08-28-2005, 09:38 PM

That's what your widget is called. LMC part # 30-0912. Glad you gotter' back together. Take care, Mike

shifty · 08-28-2005, 10:32 PM

I just pulled my 3spd tranny and L6 outta my truck. Please show me a picture of the broken part, I have one to spare.

shifty · 08-29-2005, 06:23 PM

PS - where is the little guard that is supposed to prevent outside elements from getting into your bellhousing?

08-27-2005, 08:53 PM	#1
pritch Registered User Join Date: Mar 2004 Location: Hoytsville, Utah Posts: 3,365	My bell crank broke. 30 miles from home, but just pulling away from the last stoplight I would have to stop for before home. I pushed in the clutch for third gear and something snapped and the clutch pedal went to the floor and I just kept on going. Someone pulled out in front of me and I had to downshift into 2nd with no clutch and then back into 3rd, but I never had to stop all the way home. So now I need a new bellcrank. Is there any difference in them between the I6 and the SBC? I think I have one around here somewhere, but it came out of a V8 truck. __________________ '68 Panel Project Boogie Chillin' '68 C-10 Ol' Green

08-27-2005, 09:39 PM	#3
69 longhorn Registered User Join Date: Aug 2001 Location: rock island,il,usa Posts: 5,382	Yes they are different (I6 or v8). you need the 6 pc, or if you have all the pcs,you can Have a local welder "fix" the problem. crazyL __________________ http://community.webshots.com/user/hotrodhorn

08-27-2005, 10:40 PM	#4
pritch Registered User Join Date: Mar 2004 Location: Hoytsville, Utah Posts: 3,365	Looks like differing opinions I didn't know what broke when it broke, I didn't think it was a good idea at the time to stop and see, so no, I don't have the piece that broke off I may just have to plan a trip to the junk yard to find one off a 6. No big deal, I just can't do it tomorrow. __________________ '68 Panel Project Boogie Chillin' '68 C-10 Ol' Green

08-27-2005, 10:44 PM	#5
hotrodmtodd 'Burban Legend Join Date: Apr 2005 Location: Mingo Junction OH Posts: 918	They ARE Different I will swap you one for a 6 for that V-8 one if you want. OR I can just send you out one on MON if you need it BAD. Let me know with a PM if you need it. Good luck, Mike __________________ '67 Chevy Iron City Beer Truck (9ft step) '67 Chevy Panel Truck 467 '68 Short Fleet 305v6 '68 McLaren Ramp Truck '68/'68/'70/'71 Burbs 292/366/402/454 '69 C-30 dump '71 C-50 dump and church bus '71 4x4 454 '72 Blazer (w/pop-up camper) $15 x-hooks '66 Chevy II 194/Weber '68 El Camino" 305v6 '69 Skylark 455 Buick '70 Chevelle 427 '71 Cutlass W-31 '71 GTO 400 2x2 "The 51" Chopped '51 Chevy (409) my first car OK Toad, we'll take 'em all... John Milner

08-27-2005, 10:57 PM	#6
69 longhorn Registered User Join Date: Aug 2001 Location: rock island,il,usa Posts: 5,382	it looks like you may need the bottom rod , from the bellcrank to the throw out fork also. best of luck,crazyL __________________ http://community.webshots.com/user/hotrodhorn

08-27-2005, 09:12 PM	#2
Randy70C-10 Account Suspended Join Date: Mar 2001 Location: Virginia Beach, Va. U.S.A. Posts: 15,320	Nope, no difference

08-28-2005, 06:02 AM	#7
'68OrangeSunshine Senior Member Join Date: Feb 2002 Location: Tucson, AZ USA Posts: 7,205	The V8 Z-bar is 7" across and the L6 Z-bar is 5-13/16th inches. __________________ Every 25 years I like to rebuild that 292, whether it needs it or not.

08-28-2005, 07:27 PM	#8
pritch Registered User Join Date: Mar 2004 Location: Hoytsville, Utah Posts: 3,365	Well, my buddy had one up in his boneyard. All fixed and back together. Except I still need that little widget that goes on the clutch end of the push rod. The thing that actually touches the throw out arm. I just put a big flat washer on it for now, but I want the correct part. __________________ '68 Panel Project Boogie Chillin' '68 C-10 Ol' Green

08-28-2005, 09:38 PM	#9
hotrodmtodd 'Burban Legend Join Date: Apr 2005 Location: Mingo Junction OH Posts: 918	Pushrod Nut That's what your widget is called. LMC part # 30-0912. Glad you gotter' back together. Take care, Mike __________________ '67 Chevy Iron City Beer Truck (9ft step) '67 Chevy Panel Truck 467 '68 Short Fleet 305v6 '68 McLaren Ramp Truck '68/'68/'70/'71 Burbs 292/366/402/454 '69 C-30 dump '71 C-50 dump and church bus '71 4x4 454 '72 Blazer (w/pop-up camper) $15 x-hooks '66 Chevy II 194/Weber '68 El Camino" 305v6 '69 Skylark 455 Buick '70 Chevelle 427 '71 Cutlass W-31 '71 GTO 400 2x2 "The 51" Chopped '51 Chevy (409) my first car OK Toad, we'll take 'em all... John Milner

08-28-2005, 10:32 PM	#10
shifty Questionable Join Date: Mar 2005 Location: Atlanta Posts: 13,376	I just pulled my 3spd tranny and L6 outta my truck. Please show me a picture of the broken part, I have one to spare. __________________ If I've got anything up for grabs, it'll be here: 7-hole gauge cluster for a 67-72 p/u FREE (link) I can't check the forum daily. If I don't reply to you within 24 hours, drop me a PM! I'm (hopefully) still alive and will reply faster to a PM.

08-29-2005, 06:23 PM	#11
shifty Questionable Join Date: Mar 2005 Location: Atlanta Posts: 13,376	PS - where is the little guard that is supposed to prevent outside elements from getting into your bellhousing? __________________ If I've got anything up for grabs, it'll be here: 7-hole gauge cluster for a 67-72 p/u FREE (link) I can't check the forum daily. If I don't reply to you within 24 hours, drop me a PM! I'm (hopefully) still alive and will reply faster to a PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.