![]() |
![]() |
#1 |
Registered User
Join Date: Mar 2005
Location: waco tx
Posts: 584
|
Pvc Valve
Can I hook up my Pvc valve from the valvecover to the vac on the intake.The one where the trans vac hooks up to will this work?
__________________
77 swb starting all over again. |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: Pvc Valve
i think it'd be better to use a pcv valve i think pvc will not work well
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Jun 2002
Location: Knoxville Tenn.
Posts: 3,058
|
Re: Pvc Valve
Off carb-more vacuum pull. Also it will kill fuel signal to # 8 cylinder.
__________________
56 Chevy Bel-Air 2dr. HT (purchased new) 71 Chevy Cheyenne SWB PU (502HO) 65 GMC short bed step--work in progress and my gofer Last edited by jhow66; 02-28-2006 at 11:59 PM. |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Mar 2005
Location: waco tx
Posts: 584
|
Re: Pvc Valve
The reason Im asking is I have no where to put my powerbrake at.If I use the one on the carb for the PVC valve can I put a Tee on the one on the intake and use it for the trans and powerbrake?Its a manuel choke carb. Thank you
__________________
77 swb starting all over again. |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jun 2002
Location: Knoxville Tenn.
Posts: 3,058
|
Re: Pvc Valve
Will work fine that way as the trans and booster are both closed systems.
__________________
56 Chevy Bel-Air 2dr. HT (purchased new) 71 Chevy Cheyenne SWB PU (502HO) 65 GMC short bed step--work in progress and my gofer |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Mar 2004
Location: CA
Posts: 2,057
|
Re: Pvc Valve
can you elaborate why it would kill fuel signal? i know if you didnt have it hooked to port vacuum it would loose vacuum off idle, but i dont really understand the fuel signal thng.
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Jun 2002
Location: Knoxville Tenn.
Posts: 3,058
|
Re: Pvc Valve
I will try. If you install your PCV line on the intake at that point (intake runner to #8 cylinder) you will loose most of your vacuum pull to the PCV valve itself because it is "open" to the outside air. When # 8 cylinder is on the intake stroke it cannot pull any fuel in because the port is open to the outside air the same as if the intake gasket was leaking at that port. The reason you can put your powerbrake booster and trans modulator on the intake is that they are closed to the outside air. A PCV valve is just a controled vacuum. ( The above explanation comes from a 70 year "young" gear head-me) LOL
__________________
56 Chevy Bel-Air 2dr. HT (purchased new) 71 Chevy Cheyenne SWB PU (502HO) 65 GMC short bed step--work in progress and my gofer |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|