![]() |
![]() |
#1 |
250 V-6 Club
![]() Join Date: Feb 2005
Location: San antonio, TX.
Posts: 898
|
blinker will not work
I installed new LED’s on my 70 short step side. Yesterday but for the life of me the blinker will not work
![]() Thanks
__________________
1970 Chevy C/10 6 Cyl. 43k original miles all factory ![]() Never ask a stupid question unless you want a stupid answer ![]() |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Dec 2004
Location: Arvada Colorado
Posts: 1,321
|
Re: blinker will not work
Did you install an electronic flasher? I don't know about your LED's but my kit from ECE came with an electronic flasher that was required. Just a thought.
__________________
Larry 1949 Willys CJ2A, Kubota Turbo Diesel engine, Warn Overdrive, 11 inch brakes, 12volt, Warn M8000 Winch "Little Green" 1970 Rustoleum Roller Red C20 Custom Camper 454 TH400 "Big Red" 1971 K20 6.2 Turbo Diesel 4x4 4spd Ranger Overdrive "Pumpkin Wagon" 2005 VW Beetle Diesel 44+ MPG "Silver Bullet" |
![]() |
![]() |
![]() |
#3 |
250 V-6 Club
![]() Join Date: Feb 2005
Location: San antonio, TX.
Posts: 898
|
Re: blinker will not work
No I did not. Is that something I could buy at any auto parts? also where would I hook it up to?? Thanks.
__________________
1970 Chevy C/10 6 Cyl. 43k original miles all factory ![]() Never ask a stupid question unless you want a stupid answer ![]() |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Jun 2003
Location: Northwest GA
Posts: 132
|
Re: blinker will not work
Yup, you can grab it at any parts store.
It will be the same size/PN# as your stock one, just an electronic version. Also, if after you get that done, it doesn't work still, spin the bulbs 180* in the socket, as LED's are polar sensitive.
__________________
Orange '71 GMC |
![]() |
![]() |
![]() |
#5 | |
250 V-6 Club
![]() Join Date: Feb 2005
Location: San antonio, TX.
Posts: 898
|
Re: blinker will not work
Quote:
__________________
1970 Chevy C/10 6 Cyl. 43k original miles all factory ![]() Never ask a stupid question unless you want a stupid answer ![]() |
|
![]() |
![]() |
![]() |
#6 |
67-72 Addict!
Join Date: Feb 2002
Location: The TAX State!
Posts: 7,857
|
Re: blinker will not work
I used an EL-12 flasher for my LED's.
__________________
Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads |
![]() |
![]() |
![]() |
#7 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: blinker will not work
The old mechanical flashers heat up from the amount of current that passes through... much like that single white X-mas light does. Once it gets to a certian temperature, it opens the circuit untill it is cool enough then it closes the circuit again.... like a circuit breaker.
Since LEDs run off of mili-amps, instead of multible amps, there is a huge reduction in current traveling through the flasher. Therefor, it doesn't get hot enough to open the circuit. An electric flasher.... is contrilled electronicly. |
![]() |
![]() |
![]() |
#8 |
250 V-6 Club
![]() Join Date: Feb 2005
Location: San antonio, TX.
Posts: 898
|
Re: blinker will not work
Thanks for all the great info guys.
__________________
1970 Chevy C/10 6 Cyl. 43k original miles all factory ![]() Never ask a stupid question unless you want a stupid answer ![]() Last edited by oj70chevy; 04-30-2006 at 10:18 PM. |
![]() |
![]() |
![]() |
#9 |
250 V-6 Club
![]() Join Date: Feb 2005
Location: San antonio, TX.
Posts: 898
|
Re: blinker will not work
I did try the electronic flasher and it still does not work
![]()
__________________
1970 Chevy C/10 6 Cyl. 43k original miles all factory ![]() Never ask a stupid question unless you want a stupid answer ![]() |
![]() |
![]() |
![]() |
#10 | |
Son Of Gravel Man
Join Date: Mar 2005
Location: Cleveland OH
Posts: 638
|
Re: blinker will not work
does yours have a extra ground wire? you might have to hook those up. Also check the ground for the taillight harness make sure that one is still getting good contact.
__________________
Daily driven 70 C10 longbed Its a work in progress ![]() Quote:
|
|
![]() |
![]() |
![]() |
#11 |
250 V-6 Club
![]() Join Date: Feb 2005
Location: San antonio, TX.
Posts: 898
|
Re: blinker will not work
there is 3 wires that go from the LEDs to the plug. When you say hook them up, What exactlly what do you mean?
__________________
1970 Chevy C/10 6 Cyl. 43k original miles all factory ![]() Never ask a stupid question unless you want a stupid answer ![]() |
![]() |
![]() |
![]() |
#12 | |
Son Of Gravel Man
Join Date: Mar 2005
Location: Cleveland OH
Posts: 638
|
Re: blinker will not work
mine had wires that ran to the plug and another wire just by itself. The extra wire was a ground wire. I guess yours doesn't have that.
__________________
Daily driven 70 C10 longbed Its a work in progress ![]() Quote:
|
|
![]() |
![]() |
![]() |
#13 |
I'm watching you!
Join Date: Feb 2005
Location: Levittown, PA
Posts: 1,822
|
Re: blinker will not work
__________________
2012 Chevrolet Silverado 1500 Z71 4WD 1993 Chevrolet C-1500 W/T - Blue - 4.3L V-6, 4 speed auto - Dad's (RIP) 1992 Chevrolet S10 - LS swap project 1968 Chevrolet C-10 longbed fleetside - sold ![]() |
![]() |
![]() |
![]() |
#14 |
Registered User
Join Date: Sep 2005
Location: Roseville, CA
Posts: 152
|
Re: blinker will not work
![]()
__________________
Avatar is a pic of "Before"... Just wait.. ---------------- 1969 Fleetside: Shortened frame for SWB, ECE 4-6 drop. ECE SS tank. All new ECE suspension. Rebuilt 12 bolt 3:73 with Eaton Posi. Front and rear disc brakes. Ramjet 350 and 700r-4 trans. 20" Centerline wheels with Kumho 295/45/20 tires (I hope they fit). Progress pics: http://s44.photobucket.com/albums/f2...uck/?start=all ---------------- Seriously... It's nothing a large dose of cash can't fix... Right? After all, I can't take it with me when I go... Just gotta have enough to get there!!! ![]() Last edited by rkarr; 05-01-2006 at 10:54 PM. |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|