We`ll See...Headman Elites/4spd Manual - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**special-K** · 08-29-2006, 07:52 AM

I just ordered a set of Headman Elites fir my K/20 with a 4spd manual tranny.It`s the same situation 2 or 4wd,so don`t move this because it`s a 4wd.The Elites are ceramic-coated,have 3/8" flanges,and are 14ga.tubing.I will mount them on at my daughter`s house in the little city where the exhaust shop I use is located(Frederick,MD).I can drive to the shop (loudly

) to get them to connect up to the 2 1/4" exhaust w/Walker TurboTubes already on the truck.I`m expecting to have to move one tab/arm on the z-bar to clear the driver side header,we`ll see.

c10crazy · 08-29-2006, 10:50 AM

A buddy of mine used them on a c-10 and had to dent one of the tubes to clear a spark plug. Maybe k-20 will fit better.

bryanw1968 · 08-29-2006, 11:19 AM

special-K,

You will love them. I'm assuming you got the ones with the ball joint fitting at the collector(no gaskets needed). They have a thick flange that won't warp which also means that gaskets will last a lot longer.

Lemme know how they work out.
B-dub

08-29-2006, 07:52 AM	#1
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,851	We`ll See...Headman Elites/4spd Manual I just ordered a set of Headman Elites fir my K/20 with a 4spd manual tranny.It`s the same situation 2 or 4wd,so don`t move this because it`s a 4wd.The Elites are ceramic-coated,have 3/8" flanges,and are 14ga.tubing.I will mount them on at my daughter`s house in the little city where the exhaust shop I use is located(Frederick,MD).I can drive to the shop (loudly) to get them to connect up to the 2 1/4" exhaust w/Walker TurboTubes already on the truck.I`m expecting to have to move one tab/arm on the z-bar to clear the driver side header,we`ll see. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

08-29-2006, 10:50 AM	#2
c10crazy Like a Rock! Join Date: May 2002 Location: USA Posts: 1,092	Re: We`ll See...Headman Elites/4spd Manual A buddy of mine used them on a c-10 and had to dent one of the tubes to clear a spark plug. Maybe k-20 will fit better. __________________ 69 LWB Runs great - work in progress Mess with me and you mess with the whole trailer park!

08-29-2006, 11:19 AM	#3
bryanw1968 Senior Member Join Date: Jul 2006 Location: Leander, Texas Posts: 850	Re: We`ll See...Headman Elites/4spd Manual special-K, You will love them. I'm assuming you got the ones with the ball joint fitting at the collector(no gaskets needed). They have a thick flange that won't warp which also means that gaskets will last a lot longer. Lemme know how they work out. B-dub

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.