|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
10-19-2006, 07:41 PM
|
#1 |
|
Senior Member
Join Date: Jul 2006
Location: Blountville, Tn.
Posts: 3,904
|
Drop spindle Question?????
I have a 72 short frame. What I would like to find out is. How can I tell if they used dropped spindles or if they cut the springs. or both. is there a way I can measure from point A to point B to determine if they are stock or dropped????
 
|
|
|
|
10-19-2006, 07:45 PM
|
#2 |
|
Hittin E-Z Street on Mud Tires
 
Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: Drop spindle Question?????
Stock spindle has the rotor spindle somewhat in the middle of the spindle, and a dropped spindle will have the rotor spindle somewhat near the top of the spindle assembly... hmmm, that sounds confusing
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride  American Born, Country by the Grace of God  1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! |
|
|
|
|
10-19-2006, 07:46 PM
|
#3 | |
|
sufficiently talented fool
Join Date: Jun 2006
Location: Forest Hill, MD
Posts: 2,231
|
Re: Drop spindle Question?????
Quote:
__________________
"it's impossible to be surrounded by idiots when you are part of the circle"  2003 Suburban 2002 Pontiac Montana 1981 Corvette 1966 Impala Convertible Click here to support the board |
|
|
|
|
|
10-19-2006, 07:57 PM
|
#4 |
|
Senior Member
Join Date: Jul 2006
Location: Blountville, Tn.
Posts: 3,904
|
Re: Drop spindle Question?????
O.k. so i'll take a look and see. but I wonder if there is a way to tell how much they are dropped if they are.
|
|
|
|
|
10-19-2006, 09:38 PM
|
#5 |
|
Registered User
Join Date: Oct 2002
Location: Parksville, B.C. Canada
Posts: 637
|
Re: Drop spindle Question?????
Most of the drop spindles I've seen in catalogues, etc, seem to be a 2 1/2" drop.
__________________
1969 G.M.C 3/4 Ton 920 (Canadian Version) 307 3 speed, currently apart 1998 Chevy 1/2 ton ex cab V-6 5 speed 1967 Chevy SWB - project truck; not started just yet |
|
|
|
|
10-19-2006, 09:48 PM
|
#6 | |
|
Registered User
Join Date: Sep 2006
Location: Houston, Texas
Posts: 190
|
Re: Drop spindle Question?????
Quote:
Dropped spindle on left. Stock height spindle on right. Notice difference in spindle pin position is higher in casting on dropped spindle, raising the wheel higher into inside fender.
__________________
1985 SWB Silverado 1/2 Ton 1972 Chevy SWB 1/2 Ton (sold) 1972 Chevy Chevelle SS (sold) 1971 Chevy Nova (sold) 1967 Chevy El Camino (sold) 2001 Mustang Bullitt (sold) 2019 Toyota Tundra Crewmax (daily) Last edited by novajess1972; 10-19-2006 at 09:50 PM. |
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
