wheel bearing welded to spindle - The 1947 - Present Chevrolet & GMC Truck Message Board Network

HatGuy · 12-30-2006, 12:25 AM

Looks like I need a new spindle and bearing. The only kits I find are
drop kits. Where can I buy a stock kit for a 72' K5 4X4.

72 CustomCamper · 12-30-2006, 01:44 AM

You'll probably have to goto a junkyard. Nice part is the Spindle should be the same up into the 70's as long as it's off a Dana 44 axle...

HatGuy · 12-30-2006, 07:54 AM

Thanks that is good news

How can I tell if its a Dana 44 axle ?

Livrat · 12-30-2006, 10:27 AM

Here is a link to axle identification... You will find what you need under 1971 to about 1980 chevrolet 1/2 tons 4X4's... they used either a Dana 44's or a Corporate 10 bolts.. you need one for the Dana... Left or right sides are the same..

http://coloradok5.com/axleguide.shtml

LUV2XCLR8 · 12-30-2006, 05:13 PM

Neat link Rat

66skylarkpost · 12-30-2006, 05:29 PM

pre '76 dana 44's had what was known as a small bearing spindle . after that dana enlarged the spindle and inner brearing , then in '78 gm 10 bolts carried on with the same spindle bearing setup

12-30-2006, 12:25 AM	#1
HatGuy Registered User Join Date: Aug 2003 Location: Fort Worth Texas Posts: 275	wheel bearing welded to spindle Looks like I need a new spindle and bearing. The only kits I find are drop kits. Where can I buy a stock kit for a 72' K5 4X4. __________________ Joe Peters the HatGuy 72' K5 Highlander My Daily Driver http://www.pbhats.com/BLAZER/index.html

12-30-2006, 01:44 AM	#2
72 CustomCamper huh ??? Join Date: Nov 2002 Location: Fredericksburg,Va. Posts: 3,368	Re: wheel bearing welded to spindle You'll probably have to goto a junkyard. Nice part is the Spindle should be the same up into the 70's as long as it's off a Dana 44 axle... __________________ 90 Blazer Silverado 350w/ 700R4 and 32" Kelly's "I am a bomb technician. If you see me running try to keep up!"

12-30-2006, 07:54 AM	#3
HatGuy Registered User Join Date: Aug 2003 Location: Fort Worth Texas Posts: 275	Re: wheel bearing welded to spindle Thanks that is good news How can I tell if its a Dana 44 axle ? __________________ Joe Peters the HatGuy 72' K5 Highlander My Daily Driver http://www.pbhats.com/BLAZER/index.html

12-30-2006, 10:27 AM	#4
Livrat Member #1049 Join Date: Jun 2000 Location: Troy Montana Posts: 3,940	Re: wheel bearing welded to spindle Here is a link to axle identification... You will find what you need under 1971 to about 1980 chevrolet 1/2 tons 4X4's... they used either a Dana 44's or a Corporate 10 bolts.. you need one for the Dana... Left or right sides are the same.. http://coloradok5.com/axleguide.shtml

12-30-2006, 05:13 PM	#5
LUV2XCLR8 The LuvShack Garage Join Date: Jan 2004 Location: Maple Grove, TN (West Side) Posts: 30,468	Re: wheel bearing welded to spindle Neat link Rat __________________ Owner/Op: "TN Classic Transport Carriers" The Toy: "Square Vette" 72 Hybrid Blazer Toy Barn: "LuvShack" 40 x 60 x 20 Shop Tow Piggy:"Maddy" 88 Silverado 3500 Hauler: "Feathers" 14 Aluma 8218T

12-30-2006, 05:29 PM	#6
66skylarkpost Registered User Join Date: Mar 2006 Location: kearney,nebraska Posts: 443	Re: wheel bearing welded to spindle pre '76 dana 44's had what was known as a small bearing spindle . after that dana enlarged the spindle and inner brearing , then in '78 gm 10 bolts carried on with the same spindle bearing setup __________________ '70 k-10 longbox- mid 70's drivetrain 350/350 487x heads 10.1:1 flowmasters ,35's 3.73's auburn posi ,rear shackle flip. '72 short stepside U.S. forestry truck, '73 455 buick,400 turbo,dropped 2"-4 1/4" ,3.07 posi,:'89 silverado 1500 ,OK truck ,5.7 holley tbi ,trick 700r4 3.07 auburn posi ,and my '66 skylark ,'73 centurion and my '84 monte carlo imca stock car

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.