|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-29-2006, 08:33 PM
|
#1 |
|
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Superwinch hub question... lockouts have play in them
was messing with my superwinch hubs today and noticed that both of them have some outward movement in them (1/16th - 1/8th") is that normal? Other than that they operate fine. Took one apart and the movement is due to the snaprings not holding it tight to the inside of the hub. My Milemarkers dont have "play" in them. Should I swap them out or is there some kind of spacer that might be missing, or is this normal?
Last edited by msgross; 12-29-2006 at 08:34 PM. |
|
|
|
12-31-2006, 10:27 AM
|
#2 |
|
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Re: Superwinch hub question... loskouts have
ttt
|
|
|
|
|
01-01-2007, 08:19 PM
|
#3 |
|
K5Camper
 
Join Date: Mar 2004
Location: Pueblo, CO
Posts: 1,513
|
Re: Superwinch hub question... loskouts have
My superwinch hubs have zero movement. Are you talking about the whole outer section or just the dial?
__________________
Rob Z. 1975 K5 350/465/205/D44/12b 4" lift on 35's- RIP 1991 K5 8.1L/NV4500/241/D44/14b FWC Camper |
|
|
|
|
01-01-2007, 08:26 PM
|
#4 |
|
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Re: Superwinch hub question... loskouts have
the whole outer section "pulls out" just a bit. There is slack between the inner unit and the snap rings that allows play...both hubs do it the same...
|
|
|
|
|
01-02-2007, 07:07 PM
|
#5 |
|
K5Camper
Join Date: Mar 2004
Location: Pueblo, CO
Posts: 1,513
|
Re: Superwinch hub question... loskouts have
Does your outer section have an o-ring seal on it? (it seals between the outer hub body and the tube portion of the hub assembly itself) Mine does and it seems like it's almost 1/8th of an inch. Might be why mine don't move.
__________________
Rob Z. 1975 K5 350/465/205/D44/12b 4" lift on 35's- RIP 1991 K5 8.1L/NV4500/241/D44/14b FWC Camper |
|
|
|
|
01-02-2007, 07:31 PM
|
#6 |
|
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Re: Superwinch hub question... loskouts have
maybe not..i'll have to check it out...someone might have done a brake job at one time and left them off.... they work great other than the play. O rings would hold the inside parts up against the clip rings better...thanks.
|
|
|
|
|
01-03-2007, 01:16 PM
|
#7 |
|
Registered User
Join Date: Apr 2000
Location: Chester County PA, USA
Posts: 1,228
|
Re: Superwinch hub question... loskouts have
mine didn't do that, but the directions that came with my hubs said it was ok to have in and out movement.
__________________
72 k/10 short wideside 72 k/5 Blazer 72 K/5 Blazer - obstacle course racer 72 custom/10 8' bed 70 K/5 Blazer 67 C-30 GMC Flat bed 86 GMC K2500 Plow Truck 85 GMC K3500 84 M1008 85 M1008 77 G30 Motor Home 72 Sears 12hp Tractor Glenmoore, Pennsylvania |
|
|
|
|
01-03-2007, 03:29 PM
|
#8 |
|
Registered User
Join Date: Feb 2000
Location: Modesto, CA
Posts: 1,842
|
Re: Superwinch hub question... loskouts have
On my Warns there is an Oring that seals the hub. I would guess that small amount of movement will not cause an issue other than alowing water in...possably.
I wouldn't worry too much about it. 
__________________
1972 K5 MPFI454/Sm465/Np205/D60/14FFd/Re-Centerd H1s w/Swamper Iroks
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
