|
01-01-2007, 03:59 PM
|
#1 |
|
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
WTB cab patch panels
Looking for a
1.pass (maybe driver too) floor panel 2.possibly new inner and outer rockers Both sides. 3. Is there a patch made for the area inside the cab near the corners under the gas tank? I removed my tank today and realized that the PO was using the bottom driver corner of the tank as a patch! BIG HOLE! Will send pics later... thanks.. shipping would be to 17042 Lebanon, PA. Last edited by msgross; 01-01-2007 at 06:10 PM. |
|
|
|
01-01-2007, 07:32 PM
|
#2 |
|
Senior Member
Join Date: Jul 2006
Location: Blountville, Tn.
Posts: 3,904
|
Re: WTB cab patch panels
I have got it all. I am going to be cutting up my 68 cab. If your interested let me know. The cab I am going to cut up for patch panels has an excellent floor somebody started putting in gm rockers. Let me know what you think.
|
|
|
|
|
01-01-2007, 08:14 PM
|
#3 |
|
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Re: WTB cab patch panels
sounds great...
I will get a pic tomorrow of my "problem" areas and see what you can fill in with some pieces. The only holes are in the area under the gas tank on each side.. I can see day light through one and I might be able to fit my foot through the other (and I wear 14's!) I actually removed the pass seat belt by pulling very hard! thanks.. |
|
|
|
|
01-02-2007, 08:39 PM
|
#4 |
|
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Re: WTB cab patch panels
Here is what I need... take a look at the pics and see if find other pieces. I already have cab corners and rear floor supports. thanks... I need these items by the end of January...
|
|
|
|
|
01-17-2007, 08:57 AM
|
#5 |
|
Weekend Warrior
Join Date: Oct 2004
Location: CT
Posts: 1,787
|
Re: WTB cab patch panels
I know this is a little old. I think you're better off purchasing another cab for the truck. Looks like this one has been molested many times before.
__________________
-'07 GMC Sierra K2500HD -'66 C10 Suburban -'68/'71 K20 Service Bed Project -'69 Chevy C30 Mason Dump -'33Ford P/U 396ChevyPowered   
|
|
|
|
|
01-17-2007, 09:01 AM
|
#6 |
|
Registered User
Join Date: Jul 2006
Location: Central PA
Posts: 12,201
|
Re: WTB cab patch panels
If there was a good selection around these parts then I would consider...I'm just gonna clean up all the rust areas, patch it, seal it and be done until it's next restoration when all sheet metal needs replaced. No $$ in the budget for a big resto anyway...
__________________
The Garage: 1968 K-10 SWB - "Project Money Pit" 1996 Z-71 - "huntin rig" 1969 C-10 LWB (SOLD) "Project flip that truck or else" 1993 Passport, F@rd 1-ton (SOLD)"Project Cousin Eddie" My Garage Build "The 1,000 footer" |
|
|
|
|
01-17-2007, 12:11 PM
|
#7 |
|
Registered User
Join Date: Dec 2004
Location: El paso, Tx.
Posts: 428
|
Re: WTB cab patch panels
Off topic I was wondering if it's a 2wd or a 4wd if it's a 2wd can you post some pics of how the exhaust is routed around the clutch linkage area. And what type of exhaust manifold you are running thank you for your help.
__________________
1969 Chevy C-10 350/700r4 |
|
|
|
|
01-17-2007, 12:34 PM
|
#8 |
|
Registered User
 
Join Date: Jan 2001
Location: Jackson, New Jersey
Posts: 1,560
|
Re: WTB cab patch panels
if you change your mind i may have one a bit better than that. cheap
not perfect but looks better than what you got. ill look it over good , i just picked it up this weekend btw its a 67 cab small window
__________________
2004 Silverado 2500HD Crewcab 4x4 2000 TOYOTA 4RUNNER 1971 CHEYENNE LWB (THE LOVE SHACK) 1967 c-10 lwb (THE FARMERS DAUGHTER) Last edited by jc; 01-17-2007 at 12:35 PM. |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
