I need some help, looks like I'm going to be forced to use an auto tranny. - The 1947 - Present Chevrolet & GMC Truck Message Board Network

chevybill · 03-31-2007, 01:39 PM

I have been trying to install a NV3500 manual 5 speed from a 99 s-10 4.3 truck and fabricate my clutch linkage along with a 350 vortec engine. The pic attached shows the flex line that goes to the release bearing and it is about 2 inches short!!! Where it needs to be mounted on the fire wall for the linkage (I am following Yukon's Jacks template for a mounting location on the firewall) With the clutch linkage in this location the flex line is too short to attach to the release bearing.

Basically, I am so frustrated with this I could just give up!!!!!

Anyone have a good deal on a turbo 350 automatic, I feel like this is my only alternative.

airdale94 · 03-31-2007, 10:03 PM

Hard to tell from the picture, if the line unscrews from the slave cylinder, you could have a custom one made. Might still be able to if it crimps on. Or maybe put a splice in it. Try pm'ing Yukon Jack. Or take it to a hydraulic hose shop.

jeffspower · 03-31-2007, 10:10 PM

didn't they use the same tranny in a 4.3 1/2 ton? If so, the hose would surely be longer.

jeffspower · 03-31-2007, 10:23 PM

Oreilly's shows a '99 s10 4.3 and C1500 5.0 using the same slave cylinder- I bet the C1500 hose is what you need. Probably a GM part though.

chevybill · 04-01-2007, 10:00 AM

Thanks for the replies guys, the problem finding someting to work with a truck setup if I have yet to find something like this in a complete assembly for a truck.
I am not giving up yet.

dh81k30 · 04-01-2007, 12:13 PM

chevybill,

That looks like the M/C in my '86 C10 ( 4.3 with three speed ). Maybe that application line could solve your problem.

Tx Firefighter · 04-01-2007, 12:18 PM

Chevybill.

When you buy an assembly from GM, it comes fully assembled and even bled. Everything from master cylinder, line,to the slave cylinder. Try one for a 1/2 ton fullsize.

chevybill · 04-01-2007, 02:12 PM

thanks to everyone and tx firefighter, i will check on that. it could solve my problem.

03-31-2007, 01:39 PM	#1
chevybill Senior Member Join Date: Oct 2004 Location: calhoun city ms Posts: 940	I need some help, looks like I'm going to be forced to use an auto tranny. I have been trying to install a NV3500 manual 5 speed from a 99 s-10 4.3 truck and fabricate my clutch linkage along with a 350 vortec engine. The pic attached shows the flex line that goes to the release bearing and it is about 2 inches short!!! Where it needs to be mounted on the fire wall for the linkage (I am following Yukon's Jacks template for a mounting location on the firewall) With the clutch linkage in this location the flex line is too short to attach to the release bearing. Basically, I am so frustrated with this I could just give up!!!!! Anyone have a good deal on a turbo 350 automatic, I feel like this is my only alternative. Attached Images __________________ ongoing 1970 c 10 lwb 1994 z-28 few mods.-owned since new 1978 vette silver/grey 25th anniv. paint Last edited by chevybill; 03-31-2007 at 06:31 PM.

03-31-2007, 10:03 PM	#2
airdale94 Registered User Join Date: Jan 2007 Location: Topeka,KS Posts: 778	Re: I need some help, looks like I'm going to be forced to use an auto tranny. Hard to tell from the picture, if the line unscrews from the slave cylinder, you could have a custom one made. Might still be able to if it crimps on. Or maybe put a splice in it. Try pm'ing Yukon Jack. Or take it to a hydraulic hose shop.

03-31-2007, 10:10 PM	#3
jeffspower Well, Whoop-dee-do! Join Date: Mar 2003 Location: Easton, Mo. pop.- me & scarcely a few others Posts: 2,302	Re: I need some help, looks like I'm going to be forced to use an auto tranny. didn't they use the same tranny in a 4.3 1/2 ton? If so, the hose would surely be longer. __________________ '68 GMC shortbox 4x4 350/SM465/T221- bought it in '83 SOLD '72 K20 500 Cad/TH400/NP205 SOLD '92 Chevy 2500 6.5 mech TD 4L80E crusty daily driver '72 Monte Carlo... sweet low mile toy '11 Dodge Challenger IE 392 6spd... midlife car

03-31-2007, 10:23 PM	#4
jeffspower Well, Whoop-dee-do! Join Date: Mar 2003 Location: Easton, Mo. pop.- me & scarcely a few others Posts: 2,302	Re: I need some help, looks like I'm going to be forced to use an auto tranny. Oreilly's shows a '99 s10 4.3 and C1500 5.0 using the same slave cylinder- I bet the C1500 hose is what you need. Probably a GM part though. __________________ '68 GMC shortbox 4x4 350/SM465/T221- bought it in '83 SOLD '72 K20 500 Cad/TH400/NP205 SOLD '92 Chevy 2500 6.5 mech TD 4L80E crusty daily driver '72 Monte Carlo... sweet low mile toy '11 Dodge Challenger IE 392 6spd... midlife car

04-01-2007, 10:00 AM	#5
chevybill Senior Member Join Date: Oct 2004 Location: calhoun city ms Posts: 940	Re: I need some help, looks like I'm going to be forced to use an auto tranny. Thanks for the replies guys, the problem finding someting to work with a truck setup if I have yet to find something like this in a complete assembly for a truck. I am not giving up yet. __________________ ongoing 1970 c 10 lwb 1994 z-28 few mods.-owned since new 1978 vette silver/grey 25th anniv. paint Last edited by chevybill; 04-01-2007 at 10:03 AM.

04-01-2007, 12:13 PM	#6
dh81k30 Junior Member Join Date: May 2006 Location: W-S, NC Posts: 211	Re: I need some help, looks like I'm going to be forced to use an auto tranny. chevybill, That looks like the M/C in my '86 C10 ( 4.3 with three speed ). Maybe that application line could solve your problem. __________________ Have fun, Don

04-01-2007, 12:18 PM	#7
Tx Firefighter Watch out for your cornhole ! Join Date: Jun 2003 Location: Azle, Texas Posts: 14,162	Re: I need some help, looks like I'm going to be forced to use an auto tranny. Chevybill. When you buy an assembly from GM, it comes fully assembled and even bled. Everything from master cylinder, line,to the slave cylinder. Try one for a 1/2 ton fullsize. __________________ I'm on the Instagram- @Gearhead_Kevin

04-01-2007, 02:12 PM	#8
chevybill Senior Member Join Date: Oct 2004 Location: calhoun city ms Posts: 940	Re: I need some help, looks like I'm going to be forced to use an auto tranny. thanks to everyone and tx firefighter, i will check on that. it could solve my problem. __________________ ongoing 1970 c 10 lwb 1994 z-28 few mods.-owned since new 1978 vette silver/grey 25th anniv. paint

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.