|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
05-01-2007, 03:57 AM
|
#1 |
|
Senior Member
Join Date: Feb 2006
Location: Las Vegas
Posts: 1,378
|
Factory 71-72 truck tilt parts removal??
How hard is it to remove all the parts from a factory truck tilt?
I want to replace the column seals but need help on this one! Ive done it only on non tilt columns, but is it harder on tilt columns than non tilt? Thanks. |
|
|
|
05-01-2007, 05:06 AM
|
#2 |
|
Senior Member
Join Date: Jul 2001
Location: Muskegon,MI,USA
Posts: 6,026
|
Re: Factory 71-72 truck tilt parts removal??
Disassembly of the tilt column is definitely more difficult than doing the non-tilt column. The Factory Service Manual has a good section on the process and there may be something in the FAQ's. The exploded view has been posted several times so a search may help, also.
Jim
__________________
1971 Shortbox step side 4x4, 350 sbc, 3:07 rear end 1965 Impala SS 400 sbc, Muncie rock crusher 1966 Impala SS 396 bbc, TH 400 1969 El Camino, 350 sbc, TH 350 1971 Snowplow built on a Blazer frame 1972 GMC Short bed, stepside, TH 400, 427 BBC |
|
|
|
|
05-03-2007, 01:54 PM
|
#3 |
|
Senior Member
Join Date: Feb 2006
Location: Las Vegas
Posts: 1,378
|
Re: Factory 71-72 truck tilt parts removal??
ttt. Any more opinions on how to remove the parts from it?
|
|
|
|
|
05-03-2007, 02:09 PM
|
#4 |
|
Hittin E-Z Street on Mud Tires
 
Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: Factory 71-72 truck tilt parts removal??
^Mine's in storage right now because I got stuck and couldn't get it apart any further. I've read the FAQ postings and seen the assembly manual... just can't seem to get it apart. I also don't want to bang on stuff I shouldn't. I was going to make a post like this, but I'm not in a hurry.
I've got the small metal casing and all of the turn signal and shifter stuff off. I've got the bearings loose on the bottom end, but I can't seem to get them off any further?
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride  American Born, Country by the Grace of God  1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! Last edited by 67ChevyRedneck; 05-03-2007 at 02:09 PM. |
|
|
|
|
05-03-2007, 02:41 PM
|
#5 |
|
It's a catastrophic success.
Join Date: Jan 2003
Location: Oklahoma
Posts: 2,077
|
Re: Factory 71-72 truck tilt parts removal??
Heres all the parts.LOL
|
|
|
|
|
05-03-2007, 02:47 PM
|
#6 |
|
Hittin E-Z Street on Mud Tires
Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: Factory 71-72 truck tilt parts removal??
That almost helps
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
