So who's installed power windows? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

DennyB · 10-06-2007, 11:24 AM

And where did you run the wires through the A-pillar?
I'm thinking I'll go through above the top hinge.
No need to reinvent the wheel though.
Opinions appreciated.

DennyB · 10-08-2007, 11:23 AM

No one has done this?

Sandemonium · 10-08-2007, 12:23 PM

I ran my wires just below where door pin pad is located on the A pillar. My truck did not originally have the pin that activates the interior lights, but it does now.

Hope this helps.

DennyB · 10-08-2007, 12:33 PM

Thanks for the reply.

Where did you run the wires after going through the A pillar?

I'll also be using the billet slip looms.

**1970 CST Short Wide** · 10-08-2007, 01:49 PM

Mine already had holes for speaker wire from PO. From there they went up under the dash and to the fuse box. After gluing the kick panel back in place it looks great. I used A-1's wiring harness and it worked VERY nice. My wife and kids bought them for me on fathers day and I absolutely love them

10-06-2007, 11:24 AM	#1
DennyB Led Sled! Discs R 4 ME! Join Date: Jan 2001 Location: Toms River, NJ, USA (Transplanted Hoosier) Posts: 7,327	So who's installed power windows? And where did you run the wires through the A-pillar? I'm thinking I'll go through above the top hinge. No need to reinvent the wheel though. Opinions appreciated. __________________ "Never ride faster than your Angel can fly" I.M.O.M,W,J&C Patriot Guard Rider

10-08-2007, 11:23 AM	#2
DennyB Led Sled! Discs R 4 ME! Join Date: Jan 2001 Location: Toms River, NJ, USA (Transplanted Hoosier) Posts: 7,327	Re: So who's installed power windows? No one has done this?

10-08-2007, 12:23 PM	#3
Sandemonium Proud owner of a 55.1 AD Join Date: Oct 2006 Location: Desert Hills, AZ Posts: 460	Re: So who's installed power windows? I ran my wires just below where door pin pad is located on the A pillar. My truck did not originally have the pin that activates the interior lights, but it does now. Hope this helps.

10-08-2007, 12:33 PM	#4
DennyB Led Sled! Discs R 4 ME! Join Date: Jan 2001 Location: Toms River, NJ, USA (Transplanted Hoosier) Posts: 7,327	Re: So who's installed power windows? Thanks for the reply. Where did you run the wires after going through the A pillar? I'll also be using the billet slip looms. __________________ "Never ride faster than your Angel can fly" I.M.O.M,W,J&C Patriot Guard Rider

10-08-2007, 01:49 PM	#5
1970 CST Short Wide Senior Moment Join Date: Mar 2002 Location: Pittsburg Ca Posts: 4,185	Re: So who's installed power windows? Mine already had holes for speaker wire from PO. From there they went up under the dash and to the fuse box. After gluing the kick panel back in place it looks great. I used A-1's wiring harness and it worked VERY nice. My wife and kids bought them for me on fathers day and I absolutely love them Attached Images __________________ 1970 CST LS 1 6 speed Ford 9 inch Detroit Tru Track, Dakota Didgital, Vintage Air, QA1 Coil Overs Front & Rear Lots of FUN 2013 GMC PU, Oldest Son 71 GMC LWB. QA1 Suspension, Angry SB. Youngest Son 2019 GMC Diesil Dually. Youngest Son 2017 Toyota SUV Daughters car 2018 Traverse , Wife’s Ride Pittsburg Ca 94565

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.