|
10-15-2007, 04:28 AM
|
#1 |
|
Registered User
Join Date: Oct 2007
Location: Melbourne, Australia
Posts: 41
|
vin decode
Could somebody please decode the vin off my truck. I have tried a few on the net but I'm getting incomplete answers.
CCE242Z124089 Also, as it sits everything is matching, trim tag, SPL and the chassis number. Even found the paper in the back of my seat with all the options on it. How can I find out if I have the original engine in my truck?? Any help appreciated. Last edited by Aussie_C2o; 10-15-2007 at 04:31 AM. |
|
|
|
10-15-2007, 04:42 AM
|
#2 |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: vin decode
C chevy
C 2 wheel drive E V-8 2 3/4 ton 4 Cab and bed 2 1972 Z Fremont Californiga build plant 124089 24089th truck off that assembly line at that plant |
|
|
|
|
10-15-2007, 05:19 AM
|
#3 |
|
Registered User
Join Date: Oct 2007
Location: Melbourne, Australia
Posts: 41
|
Re: vin decode
your a champ. thanks for that. would you know how i can tell if it matching engine?
|
|
|
|
|
10-15-2007, 05:57 AM
|
#4 |
|
Registered User
Join Date: Apr 2006
Location: MinneSNOWta
Posts: 1,381
|
Re: vin decode
to check the engine, right above the water pump on the passenger side, is a flat spot with numbers stamped into it (you may have to do some scraping).
on that pad, the Large numbers will be the casting code, but there will also be a partial vin stamped there, which you can compare with the trucks vin. remember, if the motor has been machined at some point, there is a chance have ground down that pad, which will make it impossible to verify for sure. the casting code on the front and rear of the engine will at least tell you if the engine is the correct year. good luck 
__________________
2003 GMC Sierra 1500 WT 1995 Nissan Hardbody 2016 Hyundai Veloster Turbo DC2 (SW/AW) Clyde W. Harvey USN "Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery" Winston Churchill |
|
|
|
|
10-15-2007, 06:32 AM
|
#5 |
|
Registered User
Join Date: Oct 2007
Location: Melbourne, Australia
Posts: 41
|
Re: vin decode
I checked this out today and the stamped number doesn't match. I will post the number tomorrow with the block casting number. I know forsure it is a 402 from the casting number and I am an engine machinist and I've already striped and prepped this engine.
Thnaks Last edited by Aussie_C2o; 10-15-2007 at 06:33 AM. |
|
|
|
|
10-15-2007, 07:30 AM
|
#6 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,861
|
Re: vin decode
If it`s a 402 engine there`s a good chance it would be a`72.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
10-15-2007, 03:57 PM
|
#7 |
|
Registered User
Join Date: Oct 2007
Location: Melbourne, Australia
Posts: 41
|
Re: vin decode
Yeah, but will the engine number be exatly the same as the vin? I have seen some US blocks with 2 numbers on the deck surface. Tis block only has one. I will take a pic today.
|
|
|
|
|
10-15-2007, 05:40 PM
|
#8 |
|
member #16
 
Join Date: Dec 1999
Location: Yuba City Ca.
Posts: 3,618
|
Re: vin decode
Here is a site to decode suffix numbers. The suffix code stamped on the front of the block will be a two or three letter code such as TKA. That will tell you the year.
http://www.nastyz28.com/decode.html
__________________
john http://67-72chevytrucks.com/vboard/showgroups.php board vendors  http://www.flickr.com/photos/1745471...7602865984234/ |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
