![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
![]() Join Date: Jan 2006
Location: Warrington, PA
Posts: 403
|
pulling motor?/block drain bolt
before pulling the motor do I need to drain the atifreeze from the block? Where is the drain bolt typically located on the block? thanks......rick
|
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Mar 2007
Location: VANCOUVER ISLAND, B.C., Canada
Posts: 1,602
|
Re: pulling motor?/block drain bolt
Yes .... the pet cock is located on the rad at the bottom.
esll.
__________________
Tomorrow is for doing today's stuff. ![]() ************************************* This truck has just the right amount of energy for me! ![]() Author: Warren Lake .... (member) Last edited by EAST SIDE LOW LIFE; 10-20-2007 at 10:51 AM. |
![]() |
![]() |
![]() |
#3 |
Senior Member
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
|
Re: pulling motor?/block drain bolt
there is do drain on the engine block
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF DONT BELIEVE EVERYTHING YOU THINK TAKE MY ADVISE;I DON'T USE IT ANYWAY |
![]() |
![]() |
![]() |
#4 |
Registered User
![]() Join Date: Jan 2006
Location: Warrington, PA
Posts: 403
|
Re: pulling motor?/block drain bolt
the rad is out I was just wondering if there was a drain bolt on the block....thanks for clearing that up for me cdowns.......rick
|
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jun 2007
Location: Netherlands
Posts: 191
|
Re: pulling motor?/block drain bolt
On my v8 small block I have one plug on each side of the block.
It can be used by a temp sensor, if you unscrew those plugs most of the fluid will be gone.
__________________
Anybody can restore a classic, takes a man to cut one up..... http://www.arnoldscustoms.com |
![]() |
![]() |
![]() |
#6 | |
Registered User
Join Date: Apr 2006
Location: MinneSNOWta
Posts: 1,381
|
Re: pulling motor?/block drain bolt
Quote:
If you are going to tear apart the engine, that will help evacuate the heads, and eliminate a possible mess ![]()
__________________
2003 GMC Sierra 1500 WT 1995 Nissan Hardbody 2016 Hyundai Veloster Turbo DC2 (SW/AW) Clyde W. Harvey USN "Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery" Winston Churchill |
|
![]() |
![]() |
![]() |
#7 |
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
|
Re: pulling motor?/block drain bolt
yep, and on putting it back together, you can actually install a petcock to where you can drain it when ever you are doing a drain/flush of the cooling system.
if you remove the plug/bolt and nothing somes out, poke the hole with a small screwdriver. |
![]() |
![]() |
![]() |
#8 |
Registered User
![]() Join Date: Jan 2006
Location: Warrington, PA
Posts: 403
|
Re: pulling motor?/block drain bolt
thanks! the motor I am pulling is a 305 so i am not going to tear into it. replacing it with a 350.
|
![]() |
![]() |
![]() |
#9 | |
Registered User
Join Date: Apr 2006
Location: MinneSNOWta
Posts: 1,381
|
Re: pulling motor?/block drain bolt
Quote:
![]()
__________________
2003 GMC Sierra 1500 WT 1995 Nissan Hardbody 2016 Hyundai Veloster Turbo DC2 (SW/AW) Clyde W. Harvey USN "Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery" Winston Churchill |
|
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|