|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
10-22-2007, 02:39 AM
|
#1 |
|
Registered User
Join Date: Dec 2006
Location: Saskatchewan
Posts: 119
|
Hooker Header Questions
I have lowered the front of my 71' 3" and the small block long tube headers I've installed are too close to the ground. I've heard there are Hooker headers that work but I don't know which ones.
Does anyone have 3/4 length Chevelle or whatever type of headers installed that work? A part number would be nice too. Thanks.
__________________
71' Chevrolet -> 350c.i. w/ 600 Edelbrock Carb, Headers, P/S, 3/5 Drop |
|
|
|
10-22-2007, 09:24 AM
|
#2 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
Re: Hooker Header Questions
I have 2452 Hooker comps(painted), on my truck. They hang 2 1/4" below the rails, @ the bottom edge of the collector flange. With a 3/5 drop on my truck, I have no ground clearance issues......if you plan on "slammin" the truck later, you may be better off going to the 3/4 lenght Chevelle headers that some of the crowd is running tho. Good luck,
 L
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
10-22-2007, 11:40 AM
|
#3 |
|
That's right, it's Copper!!
Join Date: May 2007
Location: Bakersfield, Central California
Posts: 558
|
Re: Hooker Header Questions
Like this! ECE sells these.
|
|
|
|
|
10-22-2007, 03:07 PM
|
#4 |
|
its all about the +6 inches
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,690
|
Re: Hooker Header Questions
I had the same ones that crazy mentioned, and I loved them. Good high quality item too.
|
|
|
|
|
10-22-2007, 03:57 PM
|
#5 |
|
67-72 Addict!
Join Date: Feb 2002
Location: The TAX State!
Posts: 7,856
|
Re: Hooker Header Questions
Fastom- what pulley setup is that?. Nice! Dingo dan 22- mine are pretty close also. Mine are part #2808
__________________
Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads |
|
|
|
|
10-22-2007, 04:26 PM
|
#6 |
|
That's right, it's Copper!!
Join Date: May 2007
Location: Bakersfield, Central California
Posts: 558
|
Re: Hooker Header Questions
It's the March system.
|
|
|
|
|
10-22-2007, 04:53 PM
|
#7 |
|
67-72 Addict!
Join Date: Feb 2002
Location: The TAX State!
Posts: 7,856
|
Re: Hooker Header Questions
Thanks, I'm assuming I could find it on Summitt's website or???
__________________
Jim 1970 C/10 Fleetside w/Ghost Flames Lowered 4.5" front and 4" rear (Raked) 355/350 Turbo w/shift kit 10" Redneck Performance Verter w/2500 stall Hooker Super Comps part#2808-1 Performer RPM Air-Gap 12 Bolt w/3:73 gears- Eaton Posi Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads |
|
|
|
|
10-22-2007, 05:16 PM
|
#8 |
|
That's right, it's Copper!!
Join Date: May 2007
Location: Bakersfield, Central California
Posts: 558
|
Re: Hooker Header Questions
I got it from Summit Racing.
|
|
|
|
|
10-25-2007, 03:44 AM
|
#9 |
|
Registered User
Join Date: Dec 2006
Location: Saskatchewan
Posts: 119
|
Re: Hooker Header Questions
Anyone run part number 2451?
__________________
71' Chevrolet -> 350c.i. w/ 600 Edelbrock Carb, Headers, P/S, 3/5 Drop |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
