Dirveshaft Help ???? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

tompotts · 10-15-2007, 11:24 AM

I have a 64 long/fleet. My question is do I have to use a two piece dirveshaft or can I use a 1 piece? Truck is going to have a 4/6 drop. The original driveshaft broke while driving it home and was lost. THANKS!!!

jchav62 · 10-15-2007, 01:08 PM

I think you'll be fine using a one piece, especially since your truck is lowered.

bedless66 · 10-20-2007, 06:43 PM

i have a 66 swb and i have a one piece drive shaft with a 4'' 6'' drop havent had any problems with it

factorystock · 10-22-2007, 05:14 PM

I recommend a 2 piece drive shaft with center bearing support on a long bed, like the factory installed. I was told you don't want to have a drive shaft over 72" or it will start to vibrate or go into oscillations a high speed and self destruct.

Daniel 61 Apache · 10-25-2007, 09:15 AM

Has anyone had a custom length driveshaft made? Who did you go through and how much does it run? I'm swapping out the 350 trans for a 700r4 and bagging my truck. Don't have the slightest idea where to start with the driveshaft. I was going to go to the local tranny shop and just let them do it but I'm all about saving money if I can order it on my own from someone else.

Thanks,
Daniel

Tim64 · 10-25-2007, 10:15 AM

I believe all the short beds came with the one piece drive shaft. I had a 66' long bed a few years back and it had the two piece. I think I would stick with the two piece on a long bed. A one piece drive shaft that long could cause a lot of damage if it runs out very much at all.
Tim

SIR · 10-25-2007, 01:32 PM

...we opted for a 1-piece drive shaft on our l.w.b., and no problems been 3 yrs...coast $155.00..

onebad'65 · 10-25-2007, 01:51 PM

I've purchased a assembly manual for the 60-66 trucks and strange thing is some were 2 piece drive shafts and some were single drive shafts so I think you'll be fine with just the single piece.

Daniel 61 Apache · 10-25-2007, 04:09 PM

Quote:

Originally Posted by SIR

...we opted for a 1-piece drive shaft on our l.w.b., and no problems been 3 yrs...coast $155.00..

Where did you buy it from?

Iron-Butt · 10-26-2007, 09:55 PM

I used a one piece. I measured the distance than had a new tube installed and had it balanced.

SIR · 10-26-2007, 10:27 PM

Quote:

Originally Posted by Daniel 61 Apache

Where did you buy it from?

We had it made at a local driveshaft shop here in grants pass (no longer in bussness)....

Daniel 61 Apache · 10-27-2007, 12:10 AM

Thanks. I'll give the locals a try here then.

mbgmike · 10-27-2007, 07:43 AM

Quote:

Originally Posted by Tim64

I believe all the short beds came with the one piece drive shaft. I had a 66' long bed a few years back and it had the two piece. I think I would stick with the two piece on a long bed. A one piece drive shaft that long could cause a lot of damage if it runs out very much at all.
Tim

I had a 64 swb fleet with a two piece. I replaced it with a one piece shaft

1oldtruck · 10-29-2007, 03:49 PM

Hi all, it's been a while since I logged on or posted. This subject of driveshafts puzzles me as my lwb 63 came from the factory with a one piece driveshaft. I had to have it shortened slightly when I swapped out the 3 on the tree for a TH 350 about 18 years ago. No problems with 130k miles behind a healthy 327.

Mike

skeet1261 · 11-06-2007, 01:15 PM

Tom,

Did you go to the one piece driveshaft for your long bed? If so, what length did you go with? I have wanted to go to the one piece, but was not sure if it would work. I am running a 327 with a turbo 350. Any input would be greatly appreciated.

Dean M.

Skirtchaser · 11-12-2007, 08:39 PM

Quote:

Originally Posted by 1oldtruck

Hi all, it's been a while since I logged on or posted. This subject of driveshafts puzzles me as my lwb 63 came from the factory with a one piece driveshaft. I had to have it shortened slightly when I swapped out the 3 on the tree for a TH 350 about 18 years ago. No problems with 130k miles behind a healthy 327.

Mike

Did you have any clearance issues with the 350 trany? I just thinkin'........

**ChiefRocka** · 11-13-2007, 08:37 AM

I just looked under my '63...and it too has a one-piece driveline (LWB)

10-15-2007, 11:24 AM	#1
tompotts TowMater Join Date: Jun 2007 Location: Louisville, KY Posts: 27	Dirveshaft Help ???? I have a 64 long/fleet. My question is do I have to use a two piece dirveshaft or can I use a 1 piece? Truck is going to have a 4/6 drop. The original driveshaft broke while driving it home and was lost. THANKS!!! __________________ Don't take life too seriously, you'll never get out alive.

10-15-2007, 01:08 PM	#2
jchav62 1962 C-10 Join Date: Apr 2005 Location: Las Vegas, New Mexico Posts: 4,978	Re: Dirveshaft Help ???? I think you'll be fine using a one piece, especially since your truck is lowered. __________________ Joseph Chavez "See the USA in a Chevrolet!!" ......................_____ .........________//__{\_____ ,,,,,,,/__(O)___//___/__(O)_/ 1962 C10 Shortbed Fleetside 327/th350 GV overdrive 1974 C10 Longbed Fleetside 350/th350 "The Trash Truck" 1999 Chevy 2500 OBS, Longbed 5.7/4L80E 4x4 2015 GMC Sierra SLE 1500 4x4

10-20-2007, 06:43 PM	#3
bedless66 Registered User Join Date: Jul 2007 Location: 3rd coast tx Posts: 7	Re: Dirveshaft Help ???? i have a 66 swb and i have a one piece drive shaft with a 4'' 6'' drop havent had any problems with it

10-22-2007, 05:14 PM	#4
factorystock Registered User Join Date: Feb 2007 Location: west coast Posts: 3,396	Re: Dirveshaft Help ???? I recommend a 2 piece drive shaft with center bearing support on a long bed, like the factory installed. I was told you don't want to have a drive shaft over 72" or it will start to vibrate or go into oscillations a high speed and self destruct.

10-25-2007, 09:15 AM	#5
Daniel 61 Apache Registered User Join Date: May 2007 Location: Oceanside, CA Posts: 168	Re: Dirveshaft Help ???? Has anyone had a custom length driveshaft made? Who did you go through and how much does it run? I'm swapping out the 350 trans for a 700r4 and bagging my truck. Don't have the slightest idea where to start with the driveshaft. I was going to go to the local tranny shop and just let them do it but I'm all about saving money if I can order it on my own from someone else. Thanks, Daniel

10-25-2007, 10:15 AM	#6
Tim64 Registered User Join Date: Aug 2007 Location: Vandalia, Ohio Posts: 396	Re: Dirveshaft Help ???? I believe all the short beds came with the one piece drive shaft. I had a 66' long bed a few years back and it had the two piece. I think I would stick with the two piece on a long bed. A one piece drive shaft that long could cause a lot of damage if it runs out very much at all. Tim

10-25-2007, 01:32 PM	#7
SIR SIR Join Date: Apr 2005 Location: grants pass oregon,usa Posts: 658	Re: Dirveshaft Help ???? ...we opted for a 1-piece drive shaft on our l.w.b., and no problems been 3 yrs...coast $155.00.. __________________ 66long low fleet http://community.webshots.com/user/LVNR66

10-25-2007, 01:51 PM	#8
onebad'65 Registered User Join Date: Mar 2007 Location: Lawrenceville Posts: 31	Re: Dirveshaft Help ???? I've purchased a assembly manual for the 60-66 trucks and strange thing is some were 2 piece drive shafts and some were single drive shafts so I think you'll be fine with just the single piece.

10-26-2007, 09:55 PM	#10
Iron-Butt 454 club Join Date: Oct 2002 Location: Oklahoma Posts: 1,348	Re: Dirveshaft Help ???? I used a one piece. I measured the distance than had a new tube installed and had it balanced. __________________ David 1965 Chevrolet c-10 454 automatic Custom bbw swb. 1965 Chevrolet C-10 swb (Sold) 1963 Chevrolet C-10 6 Cyl automatic with dual exhaust, pb, ps and 17's. R.I.P "I will miss you. 1967 Chevrolet C-10 6 Cyl Custom lwb 1939 Chevrolet Coupe, 350 v8 automatic. 1935 Chevrolet 2 Dr Standard in the works. 2015 Harley Davidson Street Glide. 2023 Chevrolet Stingray Z51 Convertible. I never want to grow up. Last edited by Iron-Butt; 10-26-2007 at 09:56 PM.

10-27-2007, 12:10 AM	#12
Daniel 61 Apache Registered User Join Date: May 2007 Location: Oceanside, CA Posts: 168	Re: Dirveshaft Help ???? Thanks. I'll give the locals a try here then.

10-29-2007, 03:49 PM	#14
1oldtruck Registered User Join Date: Jan 2006 Location: Los Angeles Posts: 45	Re: Dirveshaft Help ???? Hi all, it's been a while since I logged on or posted. This subject of driveshafts puzzles me as my lwb 63 came from the factory with a one piece driveshaft. I had to have it shortened slightly when I swapped out the 3 on the tree for a TH 350 about 18 years ago. No problems with 130k miles behind a healthy 327. Mike __________________ 63 Chevy LWB Stepside (current project) 01 Suburban (tow vehicle and wife's driver) 85 Toyota Truck (wife's old driver- now Home Depot runner) 04 MINI Cooper S (my commuter- don't laugh, it's a blast to drive!)

11-06-2007, 01:15 PM	#15
skeet1261 Registered User Join Date: Oct 2005 Location: St. Charles, MO Posts: 2	Re: Dirveshaft Help ???? Tom, Did you go to the one piece driveshaft for your long bed? If so, what length did you go with? I have wanted to go to the one piece, but was not sure if it would work. I am running a 327 with a turbo 350. Any input would be greatly appreciated. Dean M.

11-13-2007, 08:37 AM	#17
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,150	Re: Dirveshaft Help ???? I just looked under my '63...and it too has a one-piece driveline (LWB) __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.