![]() |
Register or Log In To remove these advertisements. |
|
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Registered User
Join Date: Feb 2002
Location: Vacaville, CA
Posts: 2,746
|
Question for anyone with a holley 4160
I got a good deal on a Holley 4160 carb (600 cfm, vac secondary) and I am wondering how people ran the fuel line to the carb. I can think of a few ways to do it, but I want to keep the rubber line to a minimum. It anyone has a picture of how they ran the line I would apreciate it.
__________________
![]() ![]() 99 Pontiac S/C GTP, SLP Ram Air hood, GMPP Konis & springs 95 Neon ACR, MP PCM, AFX UDP, 3.0 CAI |
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: May 2000
Location: Frankfort, Kentucky, USA
Posts: 2,163
|
You can make a line out of steel, just go to a auto parts store, gets some metal line, bend and flare it. Or you can get ends to screw in the carb and pump and just run a rubber line between the two. Thats what I did on my 400, works fine as long as you keep it away from moving parts.
__________________
'69 CST Short fleetside Lowered, 400 small block, 700R4, 4 wheel disc brakes, front sway bar & rear camaro sway bar (in progress) '87 V10 4x4 Short Fleetside Quad Suspension and Dual Tanks |
![]() |
![]() |
![]() |
#3 |
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,403
|
You will no doubt have to bend you own line. On the 0-1850(600 vac 2nd, & side pivot floats)they come with a "banjo fitting" with a barb for rubber hose at the fuel bowl. You can get a banjo that will accept a hard line(flairnut) through Summit racing. ill see if I can find it..... http://store.summitracing.com/partdetail.asp?part=11925
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Feb 2002
Location: Vacaville, CA
Posts: 2,746
|
I am planning to bend my own line, and I will probably use just a small amout of rubber at the end so I can put a filter in it. The problem is, when I was looking at how I would run the line, it seems like there is stuff in the way of where it would need to go. I would never put rubber line from the pump on a vehicle I own. I am just looking for a picture of a line someone bent for one of those carbs so I can copy it. If there is a fitting to hook the hard line to the carb I would be intterested in that to though.
__________________
![]() ![]() 99 Pontiac S/C GTP, SLP Ram Air hood, GMPP Konis & springs 95 Neon ACR, MP PCM, AFX UDP, 3.0 CAI |
![]() |
![]() |
![]() |
#5 |
So Many Ideas, So Little Money
Join Date: Sep 2001
Location: Marshalltown, IA
Posts: 1,610
|
you could always go with braided steal lines
__________________
72 Blazer 3/4 ton running gear 4.10s NP205/TH350 350 4in lift half doors 71 C10 with 454 99 S-10 5.1L SBC 700R4 09 Malibu ![]() Marshalltown, Iowa |
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jan 2003
Location: Chandler, AZ
Posts: 189
|
I run my stuff with hard lines, AN fittings into the mechanical pump, stainless 3/8 hard line runs up beside the water pump and along the top of the valve cover. I use the two valve cover bolts to secure my hardline and then over to the carb....another AN fitting there with a B nut on the stainless. Stainless line clamps are attatched to the valve cover bolts and hold the fuel line secure
The hard line runs right along the valve cover and basically dissapears, especially if the intake and valve covers are polished or chrome. on another car with dual 4150's it runs from the fuel pump up by the water pump, across the top of the block where the intake meets up to the drivers side of the block, straight up to 90 degree bend and into an AN tee fitting, that tee fitting is into carb 1, the back of the tee fitting has more stainless hard line back to feed carb two which has a 90 degree AN fitting. You can remove the blue anodizing from AN fittings with oven cleaner, or you can by them from some companies non-anodized. While you have the tubing out, make another line 18" long and straight, use the same line clamps and attatch it to the opposite side valve cover, now you can run your temp sender wire thru it and you wont see the wire, it will match the other side, and you eliminate some flex loom. Hopefully that makes sense? Last edited by Glen; 01-09-2003 at 09:47 PM. |
![]() |
![]() |
![]() |
#7 |
SLICER AND DICIER
Join Date: May 2001
Location: Quuen Creek
Posts: 1,383
|
Here's mine it's a 750 vac 2nd, but I think they are the same.
I bought this pre made piece with braide and an fittings from a local speed shop. But have since seen them in Checker's Auto Zone ect. In the performance section. Hope this helps ![]()
__________________
01 Tahoe 22's 2/4 drop and tv's ![]() 68 chevy money pit 51 chevy belair 95 Honda 900RR 05 GMC Siearra (company truck) |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Feb 2002
Location: Vacaville, CA
Posts: 2,746
|
That's what I wish I had. lol One like that would fit fine, but this carb has one fuel inlet one the other side, and the waterneck is right in the way.
__________________
![]() ![]() 99 Pontiac S/C GTP, SLP Ram Air hood, GMPP Konis & springs 95 Neon ACR, MP PCM, AFX UDP, 3.0 CAI |
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: Dec 2001
Location: Redding,CA...USA
Posts: 4,736
|
look in summit for there carb line kits..they have an AN- line kit complete for like35.00..it gives everything you need from pump to carb, and it looks cool
__________________
It's called "drag racing" if they called it "tic..tic..WHAM!..BANG! F*&K!!!", they'd have to keep the magazines under the counter with the other men's publications click the clicky to join the site.... http://67-72chevytrucks.com/vboard/payments.php 67 lwb..first hotrod in 25 years..540 best ET is 9.45 @ 141.44 Anderson,CA |
![]() |
![]() |
![]() |
#10 |
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,403
|
I bent a hardline for one like that Larry.......it did have some chit in the way, & wasnt fun to bend! If you take a pc of welding wire, & make the bends to go around "obsticle course", you can use it for a pattern when bending the line. You might pick up 2 pcs of line incase 1 turns out scrap.......been there & done that!
![]()
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Feb 2002
Location: Vacaville, CA
Posts: 2,746
|
Ok, I guess you see what I mean. lol I can't really see any way to bend it without putting a tight 90 degree bend in the line right before the carb. I will have to just try it and make a pattern first. That carb really doesn't seem like it was meant to go on a chevy. Maybe I should just sell it and get a dual feed one, I think that would be a lot eaiser to set up.
__________________
![]() ![]() 99 Pontiac S/C GTP, SLP Ram Air hood, GMPP Konis & springs 95 Neon ACR, MP PCM, AFX UDP, 3.0 CAI |
![]() |
![]() |
![]() |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|